Panasonic WV-NW964, WV-NS954 manual Position, Auto pan

Page 32

FOCUS buttons

Panning, tilting and zooming operations can also be car-

BRIGHTNESS buttons

ried out on the [Image/Position] tab.

Control pad/buttons

 

Refer to Operation Instructions for descriptions of how

[CLOSE] button

to operate these buttons/pad.

Click this button to close the "Preset No." setup menu.

Configure the settings relating to the auto pan function ("Auto Pan" setup menu)

Click the [SETUP>>] button of "Auto Pan" on the [Image/Position] tab of the "Camera setup" page. (page 25) The settings relating to the auto pan function can be configured with the setup menu displayed in a newly displayed window.

Position

[Left position]

Move the camera to the desired point to be set as the left point of the auto panning using the control pad/but- tons and adjust the image using the [ZOOM] buttons and the [FOCUS] buttons.

Then click the [SET] button to register the position as the left position.

[Right position]

Move the camera to the desired point to be set as the right point of the auto panning using the control pad/but- tons, and then click the [SET] button to register the posi- tion as the right position.

Notes:

Panning, tilting and zooming operations can also be carried out on the [Image/Position] tab.

Adjusted zoom and focus position for the auto pan function will be applied when [SET] button of "Start position" is clicked. These adjustments will not be applied by clicking the [SET] button of "End posi- tion".

Auto pan

[Dwell time]

Select a dwell time at the left position and the right posi- tion from the following.

5 sec/10 sec/20 sec/30 sec Default: 5 sec

[Speed]

Select a speed for the auto panning from the following. 3° /sec, 4° /sec, 5° /sec, 7° /sec, 10° /sec, 13° /sec, 18° /sec, 24° /sec

Default: 13° /sec

Note:

Even when the selected zoom factor is higher than 30x, the camera will start panning with 30x zoom factor.

Important:

When "Dwell time" or "Speed" is edited, it is neces- sary to click the [SET] button to apply them.

If these settings were configured during the auto pan operation, stop the auto panning once and resume the auto panning again.

ZOOM buttons

FOCUS buttons

BRIGHTNESS buttons

32

Image 32
Contents WV-NW964 Contents Viewer software About these operating instructionsTrademarks and registered trademarks How to display the setup menu StepHow to operate the setup menu About the setup menu window Network setup button Schedule setup buttonMaintenance button 3SetupConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status update mode Default Real timeAlarm status port Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Page Step Image capture size VGA Image capture size QvgaConfigure the settings relating to the logs LOG AlarmFTP error ManualOFF LOG tab SD memory card tab Logs and associated images SD memory Save trigger Overwrite Save logs CardSD memory Save logs CardJpeg setup Default VGA Image qualityDefault 5 fps Refresh interval JpegMPEG-4 setup Default Unicast port2 Audio Default Multicast addressDefault Multicast TTL Available value 1 DefaultDefault OFF Camera title on screen 0-9, A-Z Default 1 min Image HoldCamera title on screen Home positionTilt Angle StabilizerPan·Tilt degree/Zoom ratio display Image Adjust Preset PositionAuto Pan PatrolSuper Dynamic About SUPER-D 3 Super Dynamic functionDefault Auto Default on High Sensitivity upBlack & white mode Default High Wait timeDefault ATW1 Default High Chroma gain levelRed Gain Blue GainSet mask areas Register the preset position Edit the settings of the registered preset positionPosition No Position Auto panLearn patrol pattern GO buttonNumber of patrol pattern Zone setting Privacy zoneMode Zone selectConfigure the settings relating to audio Audio Audio modeDefault 32 kbps Audio bit rateMic input volume Camera to PC Default Middle Mic input interval Camera to PCDefault 40 msec Audio output volume PC to CameraNumber of characters for the IP address 1 Configures the multi-screen settings Multi-screen setupIP address Alarm setup Configure the alarm settings Alarm setupConfigure the settings relating to the alarm Alarm Available port number 1 Camera motion on alarmCommand alarm Originating port number Default OFF Command alarm Configure the settings relating to the alarm imageAlarm image setup To FTP setup Alarm image FTP transmissionPost alarm Transmission interval Default 1 fps Number of imagesAUX name Configure the settings relating to the alarm out terminalAlarm output terminal setup Set the VMD areas VMD area Default OFF Detection sensitivity StatusSet the VMD areas for each preset position Delete the VMD area set for the designated preset position Default MiddleMail notification setup Panasonic alarm protocol Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol setup User authentication Default OFF User namePassword Retype password Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailConfigure the settings relating to the FTP server FTP Network setup Configuring the network settings Network setupConfigure the network settings Network Default gateway Unavailable IP addresses for the default gate- wayAvailable port number 1 Default Port numbers already in use Default Manual Primary DNS, Secondary DNSWAN Configure the settings relating to Ddns Ddns Access intervalDefault OFF Host name Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp Default OFF Directory FTP periodic transmissionFTP periodic transmission Number of characters for the directory name 1Interval Schedule setupHow to configure the schedule settings How to delete the set schedule How to set the schedules Maintenance of the camera Maintenance Error messageCheck the system log System log Time & dateUpgrade the firmware Upgrade How to upgrade the firmwareInitialize setup data and Html data Initialize/restart the camera InitializationInitialize Html data RestartHelp screen Step Setup screen StepDisplaying the Help screen Category Indication Description Error indications relating to SmtpError indications relating to FTP Error indications relating to login Error indications relating to DdnsError indications relating to NTP Troubleshooting Symptom Installation Guide Cause/solution Reference Pages Installation Guide Operation Instructions Symptom Solutions Reference Pages Directory structure of drive B Group LAN IP address LAN port WAN IP address Protocol Group WAN IP address Protocol LAN IP address LAN portN0907-0 3TR005323AAB
Related manuals
Manual 21 pages 50.64 Kb

WV-NW964, WV-NS954 specifications

The Panasonic WV-NW964 and WV-NS954 are advanced network cameras designed for high-performance surveillance in various applications. Both models offer a remarkable combination of features, technologies, and characteristics that make them ideal for security monitoring in both indoor and outdoor environments.

The WV-NW964 is a high-definition network camera equipped with a 1/3-inch progressive scan CCD sensor, delivering exceptional image quality with resolutions up to 1280x960 pixels. It is particularly well-suited for situations where clarity and detail are paramount, such as in retail spaces or critical infrastructure facilities. The camera supports H.264 compression technology, which allows for efficient video streaming while maintaining high image quality. This feature is particularly useful for reducing bandwidth requirements and storage costs without compromising surveillance effectiveness.

On the other hand, the WV-NS954 is a PTZ (pan-tilt-zoom) network camera that provides extensive flexibility in monitoring wide areas. With its 3x optical zoom lens, it enables users to focus on specific subjects or areas of interest without loss of detail. The camera's ability to pan 360 degrees and tilt up to 90 degrees allows for comprehensive coverage of large spaces, making it ideal for applications such as parking lots, open-air venues, and warehouses.

Both cameras are equipped with advanced features such as digital noise reduction and wide dynamic range (WDR) technology, ensuring clear images in varying lighting conditions. The WDR feature is particularly beneficial in scenarios where backlighting can obscure details, allowing for better visibility of individuals or objects even in challenging environments. Additionally, the cameras support multiple streaming formats and resolutions, providing flexibility in how video feeds are accessed and managed across different network systems.

With built-in motion detection and event-triggered recording capabilities, both cameras enhance security by providing alerts when unusual activity is detected. Users can customize alert settings based on specific needs, ensuring efficient and timely response to potential security threats. Furthermore, both models are designed with robust IP66-rated weatherproofing, making them suitable for outdoor deployment in various weather conditions without the risk of damage.

In summary, the Panasonic WV-NW964 and WV-NS954 network cameras deliver outstanding performance through their advanced imaging technologies and versatile functionalities. With features tailored for high-quality surveillance, efficient data management, and user-friendly operation, they are essential tools for enhancing security in a variety of applications.