Panasonic WV-NW964, WV-NS954 Configure the settings relating to the alarm out terminal, AUX name

Page 42

Configure the settings relating to the alarm out terminal

Click the [Alarm] tab on the "Alarm setup" page. (pages 4 and 5: How to display/operate the setup menu)

Alarm output terminal setup

The settings relating to the alarm out terminal can be configured in this section. The settings for the alarm output ter- minal can be configured only when "Alarm output" is selected for "Terminal alarm 2" of "Alarm setup". Refer to pages 38, 39 and 41 for further information about the settings relating to the alarm, the camera action at an alarm occur- rence and the alarm image.

Note:

When "OPEN" is selected, the alarm signal will be output for around 20 seconds when the power of the camera is turned on.

[Pulse width]

When "Pulse" is selected for "Alarm output", select an alarm output terminal duration from the following. Available pulse width: 1 - 120 sec

Default: 1 sec

[Alarm output setup]

Select "ON" or "OFF" to determine whether or not to output the alarm signals to the alarm output terminal when an alarm is detected.

Default: OFF

[External terminal output setup]

Select "Latch" or "Pulse" for the alarm output terminal at an alarm occurrence.

Latch: When an alarm is detected, the alarm output ter- minal will be in the state selected for "Alarm output" until the alarm occurrence indication button is clicked.

Pulse: When an alarm is detected, the alarm output ter- minal will be in the state to the "Alarm output" setting for the period set for "Pulse width".

Default: Latch

[Alarm output]

Select "Open" or "Close" to determine whether to open or close the alarm output terminal when outputting the alarm signals.

OPEN: The alarm output terminal will open when out- putting the alarm signals. (Normally close)

CLOSE: The alarm output terminal will close when out- putting the alarm signals. (Normally open)

Default: OPEN

AUX name

The names of "AUX", "OPEN" and "CLOSE" on the "Live" page can be changed.

The name of AUX is changeable only when the terminal alarm 3 is set to AUX.

[AUX (Up to 10 characters)]

Enter the name for "AUX" on the "Live" page.

[OPEN (Up to 5 characters)]

Enter the name for "OPEN" of "AUX" on the "Live" page.

[CLOSE (Up to 5 characters)]

Enter the name for "CLOSE" of "AUX" on the "Live" page.

42

Image 42
Contents WV-NW964 Contents About these operating instructions Trademarks and registered trademarksViewer software How to display the setup menu StepHow to operate the setup menu About the setup menu window Maintenance button Network setup buttonSchedule setup button 3SetupConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status port Alarm status update modeDefault Real time Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Page Step Image capture size VGA Image capture size QvgaFTP error Configure the settings relating to the logs LOGAlarm ManualOFF LOG tab SD memory card tab Logs and associated images SD memory Save trigger Overwrite Save logs CardSD memory Save logs CardDefault 5 fps Jpeg setupDefault VGA Image quality Refresh interval JpegMPEG-4 setup Default Multicast TTL Default Unicast port2 AudioDefault Multicast address Available value 1 DefaultCamera title on screen Default OFF Camera title on screen 0-9, A-ZDefault 1 min Image Hold Home positionStabilizer Pan·Tilt degree/Zoom ratio displayTilt Angle Auto Pan Image AdjustPreset Position PatrolSuper Dynamic About SUPER-D 3 Super Dynamic functionBlack & white mode Default AutoDefault on High Sensitivity up Default High Wait timeRed Gain Default ATW1Default High Chroma gain level Blue GainSet mask areas Register the preset position Edit the settings of the registered preset positionPosition No Position Auto panGO button Number of patrol patternLearn patrol pattern Mode Zone settingPrivacy zone Zone selectDefault 32 kbps Configure the settings relating to audio AudioAudio mode Audio bit rateDefault 40 msec Mic input volume Camera to PCDefault Middle Mic input interval Camera to PC Audio output volume PC to CameraConfigures the multi-screen settings Multi-screen setup IP addressNumber of characters for the IP address 1 Configure the alarm settings Alarm setup Configure the settings relating to the alarm AlarmAlarm setup Camera motion on alarm Command alarm Originating port numberAvailable port number 1 Configure the settings relating to the alarm image Alarm image setupDefault OFF Command alarm Post alarm Transmission interval To FTP setupAlarm image FTP transmission Default 1 fps Number of imagesConfigure the settings relating to the alarm out terminal Alarm output terminal setupAUX name Set the VMD areas VMD area Default OFF Detection sensitivity StatusSet the VMD areas for each preset position Delete the VMD area set for the designated preset position Default MiddleMail notification setup Configure the settings relating to Panasonic alarm protocol Panasonic alarm protocol setupPanasonic alarm protocol Password Retype password User authenticationDefault OFF User name Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailConfigure the settings relating to the FTP server FTP Configuring the network settings Network setup Configure the network settings NetworkNetwork setup Available port number 1 Default Port numbers already in use Default gatewayUnavailable IP addresses for the default gate- way Default Manual Primary DNS, Secondary DNSWAN Default OFF Host name Configure the settings relating to Ddns DdnsAccess interval Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp FTP periodic transmission Default OFF DirectoryFTP periodic transmission Number of characters for the directory name 1Schedule setup How to configure the schedule settingsInterval How to delete the set schedule How to set the schedules Check the system log System log Maintenance of the camera MaintenanceError message Time & dateUpgrade the firmware Upgrade How to upgrade the firmwareInitialize Html data Initialize setup data and Html dataInitialize/restart the camera Initialization RestartSetup screen Step Displaying the Help screenHelp screen Step Error indications relating to Smtp Error indications relating to FTPCategory Indication Description Error indications relating to Ddns Error indications relating to NTPError indications relating to login Troubleshooting Symptom Installation Guide Cause/solution Reference Pages Installation Guide Operation Instructions Symptom Solutions Reference Pages Directory structure of drive B Group LAN IP address LAN port WAN IP address Protocol Group WAN IP address Protocol LAN IP address LAN portN0907-0 3TR005323AAB
Related manuals
Manual 21 pages 50.64 Kb

WV-NW964, WV-NS954 specifications

The Panasonic WV-NW964 and WV-NS954 are advanced network cameras designed for high-performance surveillance in various applications. Both models offer a remarkable combination of features, technologies, and characteristics that make them ideal for security monitoring in both indoor and outdoor environments.

The WV-NW964 is a high-definition network camera equipped with a 1/3-inch progressive scan CCD sensor, delivering exceptional image quality with resolutions up to 1280x960 pixels. It is particularly well-suited for situations where clarity and detail are paramount, such as in retail spaces or critical infrastructure facilities. The camera supports H.264 compression technology, which allows for efficient video streaming while maintaining high image quality. This feature is particularly useful for reducing bandwidth requirements and storage costs without compromising surveillance effectiveness.

On the other hand, the WV-NS954 is a PTZ (pan-tilt-zoom) network camera that provides extensive flexibility in monitoring wide areas. With its 3x optical zoom lens, it enables users to focus on specific subjects or areas of interest without loss of detail. The camera's ability to pan 360 degrees and tilt up to 90 degrees allows for comprehensive coverage of large spaces, making it ideal for applications such as parking lots, open-air venues, and warehouses.

Both cameras are equipped with advanced features such as digital noise reduction and wide dynamic range (WDR) technology, ensuring clear images in varying lighting conditions. The WDR feature is particularly beneficial in scenarios where backlighting can obscure details, allowing for better visibility of individuals or objects even in challenging environments. Additionally, the cameras support multiple streaming formats and resolutions, providing flexibility in how video feeds are accessed and managed across different network systems.

With built-in motion detection and event-triggered recording capabilities, both cameras enhance security by providing alerts when unusual activity is detected. Users can customize alert settings based on specific needs, ensuring efficient and timely response to potential security threats. Furthermore, both models are designed with robust IP66-rated weatherproofing, making them suitable for outdoor deployment in various weather conditions without the risk of damage.

In summary, the Panasonic WV-NW964 and WV-NS954 network cameras deliver outstanding performance through their advanced imaging technologies and versatile functionalities. With features tailored for high-quality surveillance, efficient data management, and user-friendly operation, they are essential tools for enhancing security in a variety of applications.