Panasonic WV-NS954 Configure the settings relating to audio Audio, Audio mode, Audio bit rate

Page 35

When selecting "Zone No" after selecting "Gray" for "Mode", a mask will be displayed at the center of the image display area and will start blinking while

changing its color as follows. Dark gray Light gray Clear

When the other mask that had already been set is on the same zone, the mask that had previously

been set will blink as follows. Dark gray Light gray

When selecting "Zone No" after selecting "Mosaic" for "Mode", a mask will be displayed at the center of the image display area with a mosaic effect.

When the other mask that had already been set is on the same zone, the mask that had previously been set will be displayed in dark gray.

ZOOM buttons

FOCUS buttons

BRIGHTNESS buttons

Control pad/buttons

Refer to Operation Instructions for descriptions of how to operate these buttons/pad.

[PRESET]

Select from registered preset items.

[GO] button

The camera moves to the selected preset position.

[CLOSE] button

Click this button to close the "Privacy zone" setup menu.

Configure the settings relating to audio [Audio]

Click the [Audio] tab on the "Camera setup" page. (pages 4 and 5: How to display/operate the setup menu) The settings relating to audio can be configured on this page.

[Audio mode]

Select the communication mode used for audio data transmission/reception between the camera and the PC from the following.

OFF: Does not receive/transmit audio between the cam- era and the PC. Therefore, the settings and controls relating to audio will be invalidated.

Mic input: The PC receives audio data from the cam- era. Audio can be heard with images on the PC. Images and audio will not be synchronized.

Audio output: Audio data from the PC will be transmit- ted to the camera. Audio can be heard from the speaker connected to the camera.

Interactive (half duplex): Both reception and transmis- sion are available. However, audio data cannot simultaneously be transmitted and received.

Interactive (full duplex): Both reception and transmis- sion are simultaneously available.

Note:

Howling may be generated depending on usage conditions. If howling is generated, prevent sound generated by the PC from entering the PC micro- phone.

Default: OFF

Note:

When "Multicast" is selected for "Transmission type" of "MPEG-4 setup" in the "MPEG-4 setup" section of the [JPEG/MPEG-4] tab of the "Camera setup" page (page 21), it is impossible to carry out the "Audio output" operation while monitoring MPEG-4 image. To carry out the "Audio output" operation, click the [JPEG] button.

[Audio bit rate]

Select "16 kbps" or "32 kbps" for the audio bit rate used to transmit/receive audio data.

Default: 32 kbps

35

Image 35
Contents WV-NW964 Contents Viewer software About these operating instructionsTrademarks and registered trademarks Step How to display the setup menuHow to operate the setup menu About the setup menu window 3Setup Network setup buttonSchedule setup button Maintenance buttonConfigure the basic settings Basic Configure the basic settings of the camera Basic setupDefault on Alarm status update modeDefault Real time Alarm status portConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Page Step Image capture size Qvga Image capture size VGAManual Configure the settings relating to the logs LOGAlarm FTP errorOFF SD memory Save trigger Overwrite Save logs Card LOG tab SD memory card tab Logs and associated imagesSave logs Card SD memoryRefresh interval Jpeg Jpeg setupDefault VGA Image quality Default 5 fpsMPEG-4 setup Available value 1 Default Default Unicast port2 AudioDefault Multicast address Default Multicast TTLHome position Default OFF Camera title on screen 0-9, A-ZDefault 1 min Image Hold Camera title on screenTilt Angle StabilizerPan·Tilt degree/Zoom ratio display Patrol Image AdjustPreset Position Auto PanAbout SUPER-D 3 Super Dynamic function Super DynamicDefault High Wait time Default AutoDefault on High Sensitivity up Black & white modeBlue Gain Default ATW1Default High Chroma gain level Red GainSet mask areas Edit the settings of the registered preset position Register the preset positionPosition No Auto pan PositionLearn patrol pattern GO buttonNumber of patrol pattern Zone select Zone settingPrivacy zone ModeAudio bit rate Configure the settings relating to audio AudioAudio mode Default 32 kbpsAudio output volume PC to Camera Mic input volume Camera to PCDefault Middle Mic input interval Camera to PC Default 40 msecNumber of characters for the IP address 1 Configures the multi-screen settings Multi-screen setupIP address Alarm setup Configure the alarm settings Alarm setupConfigure the settings relating to the alarm Alarm Available port number 1 Camera motion on alarmCommand alarm Originating port number Default OFF Command alarm Configure the settings relating to the alarm imageAlarm image setup Default 1 fps Number of images To FTP setupAlarm image FTP transmission Post alarm Transmission intervalAUX name Configure the settings relating to the alarm out terminalAlarm output terminal setup Set the VMD areas VMD area Status Default OFF Detection sensitivitySet the VMD areas for each preset position Default Middle Delete the VMD area set for the designated preset positionMail notification setup Panasonic alarm protocol Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol setup Number of characters for the password 4 32 char User authenticationDefault OFF User name Password Retype passwordDefault OFF Access level Host authenticationConfigure the settings relating to the mail server Mail Configure the settings of the servers Server setupConfigure the settings relating to the FTP server FTP Network setup Configuring the network settings Network setupConfigure the network settings Network Default Manual Primary DNS, Secondary DNS Default gatewayUnavailable IP addresses for the default gate- way Available port number 1 Default Port numbers already in useWAN Number of characters for the host name 1 64 char Configure the settings relating to Ddns DdnsAccess interval Default OFF Host nameConfigure the settings relating to Snmp Snmp Number of characters for the directory name 1 Default OFF DirectoryFTP periodic transmission FTP periodic transmissionInterval Schedule setupHow to configure the schedule settings How to delete the set schedule How to set the schedules Time & date Maintenance of the camera MaintenanceError message Check the system log System logHow to upgrade the firmware Upgrade the firmware UpgradeRestart Initialize setup data and Html dataInitialize/restart the camera Initialization Initialize Html dataHelp screen Step Setup screen StepDisplaying the Help screen Category Indication Description Error indications relating to SmtpError indications relating to FTP Error indications relating to login Error indications relating to DdnsError indications relating to NTP Troubleshooting Symptom Installation Guide Cause/solution Reference Pages Installation Guide Operation Instructions Symptom Solutions Reference Pages Directory structure of drive B Group WAN IP address Protocol LAN IP address LAN port Group LAN IP address LAN port WAN IP address ProtocolN0907-0 3TR005323AAB
Related manuals
Manual 21 pages 50.64 Kb

WV-NW964, WV-NS954 specifications

The Panasonic WV-NW964 and WV-NS954 are advanced network cameras designed for high-performance surveillance in various applications. Both models offer a remarkable combination of features, technologies, and characteristics that make them ideal for security monitoring in both indoor and outdoor environments.

The WV-NW964 is a high-definition network camera equipped with a 1/3-inch progressive scan CCD sensor, delivering exceptional image quality with resolutions up to 1280x960 pixels. It is particularly well-suited for situations where clarity and detail are paramount, such as in retail spaces or critical infrastructure facilities. The camera supports H.264 compression technology, which allows for efficient video streaming while maintaining high image quality. This feature is particularly useful for reducing bandwidth requirements and storage costs without compromising surveillance effectiveness.

On the other hand, the WV-NS954 is a PTZ (pan-tilt-zoom) network camera that provides extensive flexibility in monitoring wide areas. With its 3x optical zoom lens, it enables users to focus on specific subjects or areas of interest without loss of detail. The camera's ability to pan 360 degrees and tilt up to 90 degrees allows for comprehensive coverage of large spaces, making it ideal for applications such as parking lots, open-air venues, and warehouses.

Both cameras are equipped with advanced features such as digital noise reduction and wide dynamic range (WDR) technology, ensuring clear images in varying lighting conditions. The WDR feature is particularly beneficial in scenarios where backlighting can obscure details, allowing for better visibility of individuals or objects even in challenging environments. Additionally, the cameras support multiple streaming formats and resolutions, providing flexibility in how video feeds are accessed and managed across different network systems.

With built-in motion detection and event-triggered recording capabilities, both cameras enhance security by providing alerts when unusual activity is detected. Users can customize alert settings based on specific needs, ensuring efficient and timely response to potential security threats. Furthermore, both models are designed with robust IP66-rated weatherproofing, making them suitable for outdoor deployment in various weather conditions without the risk of damage.

In summary, the Panasonic WV-NW964 and WV-NS954 network cameras deliver outstanding performance through their advanced imaging technologies and versatile functionalities. With features tailored for high-quality surveillance, efficient data management, and user-friendly operation, they are essential tools for enhancing security in a variety of applications.