Panasonic WV-CS574 operating instructions Alarm Input/Output Alarm IN/OUT, CNT-CLS 1, 2 Output

Page 40

Alarm Input/Output (ALARM IN/OUT)

Move the cursor to ALARM IN/OUT, and press the CAM (SET) button. The ALARM IN/OUT submenu appears.

** SPECIAL

1 **

PRIVACY ZONE

OFF

PROPO.P/T

ON

AREA TITLE

ON(USER)

PATROL

STOP

ALARM IN/OUT

 

 

 

CLEANING

OFF

EL-ZOOM

ON

PRESET ALM

OFF

IMAGE HOLD

OFF

TILT ANGLE

0°

RET

 

 

 

Note:

While the camera is in the AF mode or the lens moves between WIDE and TELE, alarm input may be ignored if several alarm inputs are received in succession.

ALARM IN 1-4

Alarm input signals are supplied from external devices through the ALARM IN connector to turn the camera to a preset position.

1.Move the cursor to ALARM IN 1* and select a preset position or OFF with the joystick, then press the CAM (SET) button.

The factory default setting is OFF.

**

ALARM IN/OUT **

ALARM

IN

1

OFF

 

ALARM

IN

2

OFF

ALARM

IN

3

OFF

ALARM

IN

4

OFF

CNT-CLS 1

 

OFF

TIME

OUT

 

100MS

CNT-CLS 2

 

OFF

COAX ALM OUT

OFF

RET

*Set ALARM IN 2, 3 and 4 in the same way as ALARM IN 1.

1POSI, 2 POSI, 3 POSI and 4 POSI: Preset posi- tion. If an alarm input is received, the camera turns to a preset position, and sends an alarm output signal. The position number corresponds to the alarm input number (1-1,2-2,3-3 and 4-4).

OFF: The camera ignores alarm inputs.

CNT-CLS 1, 2 (Output)

Two contact closure signals (Open collector type) are output through the Alarm Output connector.

1.Move the cursor to CNT-CLS 1, and select OFF, ALARM or AUX 1 with the joystick.

The factory default setting is OFF.

When ALARM is selected, TIME OUT appears. Select an appropriate duration from among 100 MS, 200 MS, 1000 MS (1 s), 2000 MS (2 s) and 4000 MS (4 s) with the joystick. (unit: s)

The factory default setting is 100 MS. (unit: ms)

Note:

The shorter the duration, the more frequent will be the detection output.

2.Move the cursor to CNT-CLS 2, then select OFF, AUX 2 with the joystick.

The factory default setting is OFF.

OFF: Contact closure signals are deactivated.

ALARM: Available for CNT-CLS 1 only. A motion detection signal is output.

AUX 1(2): An alarm signal is output when the cam- era receives a command from the controller.

Note:

It is recommended to set the connected external device to ignore the shorter alarm outputs of 90 ms or less from the camera.

COAXIAL ALARM OUT

Alarm output signals are supplied through the coaxial cable.

1.Move the cursor to COAX ALM OUT and select ON or OFF.

2.Press the CAM (SET) button.

The factory default setting is OFF.

ON: The camera sends an alarm output signal after it turns to a preset position.

OFF: The camera does not send an output signal.

Notes:

The camera ignores alarm inputs during manual operation.

To download or upload preset data to the system controller, select “OFF”.

-40-

Image 40
Contents Operating Instructions English Version Important Safety Instructions EnglishDisclaimer of Warranty Limitation of LiabilityAccessories FeaturesOptional Accessories Precautions About the Camera Cleaning Function Contents Construction Installation Precautions Camera Installation LocationWiring the Camera Noise interference considerationsCommunication Parameters DIP Switch DIP Switch SettingsBeware of high humidity Unit Number DIP Switch RS485 Communication Parameters DIP Switch Camera Installation Installing the CameraCutout in Diecast Case Cutout in Decoration CoverSideway Cable Exit Top Cable ExitUninstalling the Camera Uninstalling the CameraPrecautions Accessory Connector InformationHow to Assemble the Cable with the Accessory Connector ConnectionsRS485 Connection RS485 Setup OFF ↔ 100MS ↔ 200MS ↔ 400MS ↔ 1000MSUsing the Setup Menu Setup MenuPage Setup Menu Description Special 1 Menu CameraALC Mode with BLC OFF Shutter Speed ShutterGain Control AGC Synchronization SyncAuto Focus AF Mode RS485 Communication10Special 2 Menu SPECIAL2 11Self-diagnosis FunctionPreset Menu Setting ProceduresMenu Display To Set Panning/Tilting Positions Position Setting Position SETPan Offset Preset Identification Setting Preset ID To Enter a New Preset IDTo Copy a Preset ID from Another Position To Set the Lens Zoom and Focus PositionsLight Control Setting ALC/MANUAL To Change an Entered Preset IDTo Delete an Entered Preset ID To Set a Display Position for a Preset IDScene File Setting Scene File Preset Speed Setting Preset SpeedTo Return to the Preset Number Set Menu To Return to the Setup MenuHome Position Setting Home Deleting Preset PositionsSelf Return Setting Self Auto Mode Selection Auto ModeAuto Pan Key Setting Auto PAN KEY SEQ Sort PatrolDigital Flip Setting Digital Flip Password VerificationNew Password Special 1 Menu Setting SpecialPrivacy Zone Privacy Zone Proportional Pan/Tilt PROPO. P/T Zoom ratioSetting for on User Settings for on NeswArea Title Area Title To Quit Editing Patrol-learn and Patrol Play PatrolArea Title Editing Patrol Learn with a Controller Having Patrol Button Patrol-learn with a Controller not Having the Patrol ButtonPatrol Play with a Controller Having the Patrol Button Patrol Play with a Controller not Having the Patrol ButtonAlarm Input/Output Alarm IN/OUT CNT-CLS 1, 2 OutputPreset Alarm Preset ALM Cleaning CleaningElectronic Zoom EL-ZOOM Camera Setting To Display the Camera Setting MenuImage Hold Image Hold Tilt Angle Tilt Angle 0 /5Move the cursor to the BLC parameter and select on Shutter Speed Setting Shutter Line-lock Sync Mode LL Gain Control AGC on LOW/ MID/ HIGH/OFFElectronic Sensitivity Enhancement Sens UP Synchronization SyncAuto-Tracing White Balance Mode ATW1/ ATW2 White Balance White BALAutomatic White Balance Control Mode AWC Motion Detector Motion DETAuto Focus Setting AF Mode Auto S Auto M Auto L Manual L Manual M Manual SSpecial 2 Menu SPECIAL2 Digital Noise Reduction DNRTo Restore the Camera Default Position Refresh Reset to the Factory Default SettingsFactory Default Setting Menu SettingSpecifications HighPage Controller Operation Setting ShortcutsIris Close Troubleshooting ProblemProblem Periodically check the power cord and plug Page Panasonic Canada Inc

WV-CS574 specifications

The Panasonic WV-CS574 is a sophisticated surveillance camera renowned for its advanced features and versatile technologies designed to enhance security applications. This camera is particularly well-suited for both indoor and outdoor use, making it a popular choice for monitoring public spaces, commercial properties, and other critical areas.

One of the standout features of the WV-CS574 is its exquisite image quality. Equipped with a high-resolution 1/4-inch CCD sensor, the camera delivers clear and crisp images at a resolution of 480 TV lines. This ensures that even in challenging lighting conditions, the camera can maintain its performance, providing reliable surveillance footage for security personnel.

The WV-CS574 incorporates a powerful 18x optical zoom lens combined with a 12x digital zoom, allowing for detailed close-ups of objects or individuals that may be far from the camera. This flexibility is crucial for identifying faces and license plates from a considerable distance. The camera also supports automatic focus, which simplifies the process of capturing sharp images, minimizing the chances of blurry footage.

Panasonic ensures that the WV-CS574 can adapt to a variety of environmental conditions through features like automatic backlight compensation and digital noise reduction. These technologies work together to optimize the camera's performance in varying light situations, whether it’s bright sunlight or dimly lit areas. Additionally, the camera’s wide dynamic range (WDR) capability helps balance the exposure levels in scenes with both bright and dark areas, resulting in clear images without loss of detail.

The WV-CS574 is designed with ease of use in mind, featuring a user-friendly interface that simplifies configuration and operation. Its pan-tilt-zoom (PTZ) capabilities offer a comprehensive monitoring solution, allowing operators to remotely control the camera's movement for real-time surveillance. The camera can pan 360 degrees and tilt 90 degrees, providing extensive coverage of the monitored area.

Moreover, the Panasonic WV-CS574 is built to withstand harsh environments, with an IP66 rating for weather resistance. This makes it suitable for outdoor installations where exposure to rain, dust, and extreme temperatures is a concern.

The camera supports various video formats, ensuring compatibility with different surveillance systems. Additionally, features like alarm inputs and outputs facilitate integration with other security devices, enhancing overall monitoring capabilities. With its combination of high-quality imaging, robust design, and versatile functionality, the Panasonic WV-CS574 stands out as an exceptional choice for any surveillance needs.