Panasonic WV-CL920A operating instructions Burst BW

Page 37

Default: OFF

AUTO1: The camera selects black and white mode if the picture is dark, or color mode if the pic- ture is bright enough.

Note: Color picture switches to black-and- white picture and vice versa in approxi- mately 1 or 2 minutes after recognition of illuminance.

AUTO2: Applying AUTO1 may cause malfunction when using a source of near-infrared light at night because the illuminance changes signifi- cantly when switching between the color pic- ture and the black-and-white picture. But AUTO2 allows the unit to prevent malfunction because it simply recognizes a source of light. Note: Because a source of light is simply rec-

ognized based on the information from CCD image pickup element, an object sometimes can not be recognized suc- cessfully when the object is always mov- ing or the object and its background have the same color.

When you apply this mode, AUTO2, the wavelength of the light source should be 800 nm or more.

ON: Black and white mode is selected.

OFF: Color mode is selected.

** SPECIAL **

 

UP SIDE DOWN

OFF

 

CHROMA GAIN

....I....

AP GAIN

....I....

PEDESTAL

....I....

HUE

....I....

BW

-

 

+

OFF

 

 

BURST (BW)

ON

 

 

CAMERA RESET

PUSH SW

 

RET END

 

 

 

10.7 BURST (BW)

1.Move the cursor to the BURST (BW) parameter.

2.Select ON or OFF using or . Default: ON

ON: The burst signal is supplied along with the black and white composite video signal.

OFF: The burst signal is not output.

Note: We recommend that you usually select ON.

** SPECIAL **

 

UP SIDE DOWN

OFF

 

CHROMA GAIN

....I....

AP GAIN

....I....

PEDESTAL

....I....

HUE

....I....

 

-

 

+

BW

OFF

 

BURST (BW)

ON

 

 

CAMERA RESET

PUSH SW

 

RET END

 

 

 

-38-

Image 37
Contents Operating Instructions Bol, within an equilateral triangle, is Contents Preface FeaturesClean the CCD faceplate with care PrecautionsDo not attempt to disassemble the camera Handle the camera with careWV-CL924 Major Operating Controls and Their FunctionsFlange-back Adjusting Ring FB Auto Iris Lens Connector0Gen-lock Termination Switch Hi-Z, G/L 75Ω 1Gen-lock Input Connector GEN-LOCK4AC/DC Compatible Input Terminal DC 12V IN/AC 24V 3Power Cord SocketWV-CL920 120 V AC 60Hz ConnectionsWV-CL924 12 V DC/24 V AC Recommended wire gauge sizes for 24 V AC line AC Power SupplyInstallation of Auto Iris Lens Connector Mounting the Lens Focus or FLANGE-BACK Adjustment Mounting from the top Installation of CameraCamera Setup Menu SetupATW1 ATW2 AWC Press and hold down for 2 seconds or more Opening the Setup MenuAll Reset Operation Setup OperationImportant Notice Editing the CAM SET UP MenuCamera Identification Camera ID Setting Setting ProceduresTo edit the Camera ID To enter a blank space in the Camera IDTo erase all characters in the editing area Light Control Setting ALC/ELCTo determine the display position of the Camera ID Back Light Compensation Back Light Comp ALC Mode with Preset onALC Mode with Preset OFF Blinking Gain Control Setting AGC ON/OFF Shutter Speed Setting ShutterElectronic Sensitivity Enhancement Sens UP Important Notices Synchronization Setting SyncVBS Gen-lock Mode Extvbs Page Line-lock Sync Mode LL VS Gen-lock Mode ExtvsPhase Coarse Auto-Tracing White Balance Mode ATW White Balance Setting White BALATW1 Auto Tracing White Balance Select AWC → Manual Fine Adjustment for AWC ATWMotion Detector Setting Motion DET Lens Drive Lens Drive Signal SelectionSpecial Menu Special Burst BW Prevention of Blooming and Smear To reset to the factory settingsAGC SpecificationsPage Standard Accessories Optional Accessories Panasonic Canada Inc