Panasonic WV-CL920A operating instructions Preface, Features

Page 4

PREFACE

Panasonic's WV-CL920 (WV-CL924) series digital color camera introduces a new level of high picture quality and high resolution through the use of a 1/2-inch frame interline transfer CCD image sensor having 768 hori-

zontal pixels (picture elements), and digital signal pro- cessing LSI's. This model offers cutting-edge technolo- gy for advanced video surveillance.

FEATURES

1.The following functions are built in.

(1)Auto Light Control (ALC)/Electronic Light Control (ELC)

(2)Back Light Compensation (Auto: Factory pre-

set, Manual: Manual photometric measuring area set)

(3)Various External Sync Functions, including Gen-Lock

(4)Auto/Manual White Balance Function

(5)Electronic Shutter Function

2.Signal-to-noise ratio of 50 dB

3.Minimum illumination of 0.3 lux (0.03 footcandle) with F1.4 lenses (Color mode)

4.Minimum illumination of 0.02 lux (0.002 footcandle) with F1.4 lenses (Black and White mode)

5.570 lines of horizontal resolution (Black and White mode)

480 lines of horizontal resolution (Color mode)

6.High quality picture:

(a)2H type vertical enhancer for greater picture sharpness

(b)Chroma averaging circuit for better color sig- nal to noise ratio

(c)Minimum of aliasing on fine objects

(d)Expanded dynamic range by use of knee cir- cuit

(e)Highlight aperture correction for greater pic- ture detail of bright objects

7.Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC) function.

8.Selectable electronic sensitivity enhancing modes including: AUTO, MANUAL and OFF

9.Built in Digital Motion Detector

10.Auto Black/White mode enables the camera to switch between C/L and B/W in response to input lights.

-4-

Image 4
Contents Operating Instructions Bol, within an equilateral triangle, is Contents Features PrefacePrecautions Clean the CCD faceplate with careDo not attempt to disassemble the camera Handle the camera with careMajor Operating Controls and Their Functions WV-CL924Auto Iris Lens Connector Flange-back Adjusting Ring FB0Gen-lock Termination Switch Hi-Z, G/L 75Ω 1Gen-lock Input Connector GEN-LOCK3Power Cord Socket 4AC/DC Compatible Input Terminal DC 12V IN/AC 24VWV-CL920 120 V AC 60Hz ConnectionsWV-CL924 12 V DC/24 V AC AC Power Supply Recommended wire gauge sizes for 24 V AC lineInstallation of Auto Iris Lens Connector Mounting the Lens Focus or FLANGE-BACK Adjustment Installation of Camera Mounting from the topSetup Camera Setup MenuATW1 ATW2 AWC Opening the Setup Menu Press and hold down for 2 seconds or moreSetup Operation All Reset OperationEditing the CAM SET UP Menu Important NoticeSetting Procedures Camera Identification Camera ID SettingTo edit the Camera ID To enter a blank space in the Camera IDTo erase all characters in the editing area Light Control Setting ALC/ELCTo determine the display position of the Camera ID ALC Mode with Preset on Back Light Compensation Back Light CompALC Mode with Preset OFF Blinking Shutter Speed Setting Shutter Gain Control Setting AGC ON/OFFElectronic Sensitivity Enhancement Sens UP Synchronization Setting Sync Important NoticesVBS Gen-lock Mode Extvbs Page VS Gen-lock Mode Extvs Line-lock Sync Mode LLPhase Coarse Auto-Tracing White Balance Mode ATW White Balance Setting White BALATW1 Auto Tracing White Balance Manual Fine Adjustment for AWC ATW Select AWC →Motion Detector Setting Motion DET Lens Drive Signal Selection Lens DriveSpecial Menu Special Burst BW To reset to the factory settings Prevention of Blooming and SmearSpecifications AGCPage Standard Accessories Optional Accessories Panasonic Canada Inc