Axis Communications 2 user manual Appendix B Updating the Firmware, Update via FTP

Page 43

AXIS 230

Updating the Firmware

43

Appendix B - Updating the Firmware

The AXIS 230 firmware is stored in Flash memory. This memory is provided by a silicon chip that, just like any other ROM device, retains data content even after power is removed. Flash memory is unique because it allows its data to be erased and re-written. This means firmware upgrades can be installed as they become available - without having to replace any parts. New firmware is simply loaded into the AXIS 230 over the network.

The latest version of the AXIS 230 firmware is available free of charge from the Axis web site at www.axis.com

Update via FTP

The AXIS 230 Flash memory is updated over the network using FTP. See the detailed instructions supplied with each new firmware release.

Important!

•Always read the instructions provided with each new release, before updating the firmware.

•Upgrading normally takes between 30 seconds and 10 minutes, although it can take longer. After starting the process, you should always wait at least 20 minutes before power-cycling the AXIS 230 - even if you suspect the procedure has failed.

•In controlled environments, flash memory updates provide a very safe way of updating the firmware. However, flash products can become damaged if the update is not performed correctly. Your dealer reserves the right to charge for any repair attributable to faulty updating by the user.

Emergency Recovery Procedure

If power or the network connection to the AXIS 230 is lost during the upgrade, the process will fail and the unit will become unresponsive. A flashing red Status LED indicates a failed upgrade. To recover the unit, follow the steps below. The serial number is found on the label on the product's casing.

1.Unix/Linux - From the command line type the following: arp -s <IP address of AXIS 230> <Serial number> temp ping -s 408 <IP address of AXIS 230>

Windows - From a command/DOS prompt type the following: arp -s <IP address of AXIS 230> <Serial number>

ping -l 408 -t <IP address of AXIS 230>

2.If the unit does not reply within a few seconds, restart it and wait for a reply. Press CTRL+C to exit ping.

Image 43

Contents Axis 230 MPEG-2 Network Camera User’s Manual Legal Considerations Safety Notices Used in This ManualAxis Support Services About This DocumentTable Of Contents Appendix a Troubleshooting Battery should not be replaced unless required Safety Notice Battery ReplacementIntroduction Features and BenefitsAxis Introduction Applications Axis 230 Front Product DescriptionAxis 230 Rear Panel Title/Variant Quantity Hardware InventoryInstallation using Axis IP Utility Installing the AxisManual Installation with ARP and Ping Client System Requirements Axis Media Control Viewing Client Configuring audio equipment Accessing the Axis 230 from Internet ExplorerOperating the Axis Accessing and logging on to the AxisFocus bar Autofocus button Access from a browserSetup tools Live ViewAuto button Setup ToolsPositional Control of the Video Source Focus barResolution Video SettingsAdvanced Settings Live View Layout Audio SettingsEvents and Event Types Configuring Event TypesGeneral Setting up a new event typeRespond to Trigger Trigger Type When TriggeredOperating the Axis Adding an Upload Server Upload ServersNotification Servers Port Status Port Status & DevicesDevices Preset position setup Pan, Tilt & Zoom Preset position setup Zoom onlySystem Options Accessing The System OptionsSystem Options Overview Administration DescriptionUsers Adding Allowed IP Addresses Firewall SettingsAdding Users Editing and Deleting UsersCurrent Server Time Date & TimeNew Server Time Parameter Description TCP/IP Network SettingsAutomatic IP Configuration Dynamic IP Address Notification SettingsNetwork Traffic Manual IP ConfigurationRTP Multicast Settings Smtp email Network SettingsIO Ports Ports & DevicesCOM Ports RS-232/RS-485 Support Logs & Reports MaintenanceFactory Default Settings Server Report Appendix a TroubleshootingChecking the Firmware SupportSymptoms Possible causes Remedial actions Symptoms, Possible Causes and Remedial ActionsMic or audio input device Ping Reply Interpretation and recommendation Pinging Your IP AddressEmergency Recovery Procedure Update via FTPAppendix B Updating the Firmware Updating the Firmware Axis Appendix C Customizing The Axis Configuration via FTPModifying the File System Custom Web Pages Customizing ProceduresEditing and Storing Your Web These lines should be added to the file as shown below Using your own file as a New HomeOr, if PTZ is enabled Terminal Block Pinout D-Sub ConnectorAppendix D Unit Connections Terminal BlockSchematic Diagram Terminal Connector Block Installation Procedure Connecting Pan/Tilt DevicesBrowser Administration Tools Querying the Status of Digital Inputs Controlling and MonitoringTransistor Output Digital InputsExample Monitor data on inputs 1 Appendix E Audio Settings Appendix F Technical Specifications Technical Specifications Axis Video Quality Level Appendix G BandwidthVideo Quality vs. Bit Rate Unicast Multicast Other ConsiderationsIndex IndexIndex Axis Smtp Glossary of Terms

Related manuals

Manual 6 pages 28.49 Kb