Samsung SNC-M300 user manual

Page 3

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

CAUTION

1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibration or magnetic interference.

2.Do not install in a location subject to high temperature (over 122°F), low temperature (below 14°F), or high humidity. Doing so may cause fire or electric shock.

3.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

4.Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or damage to the product.

5.Keep out of direct sunlight and heat radiation sources. It may cause fire.

6.Install it in a place with good ventilation.

7.Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the CCD image sensor.

8.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

9.The Mains plug is used as a disconnect device and shall stay readily operable at any time.

Image 3

Contents SNC-M300 Safety precautions Page Important safety instructions Contents Using the Camera Setting UpFeatures Precautions Installation and UsePreparation Checking the components in the package Recommended PC SpecificationsCompatible PoE Switches Compatible IP RoutersFront Names of Each PartRear Description When using the CS lens Installation and connectionInstalling the Camera Disconnect the power cord before installation or relocationCase of the lens with no zooming function Adjusting the back focusInserting/Removing an Sdhc Memory Card Selecting a memory card that’s suitable for you What is a memory card?Contacts Lock Switch Memory Card Information not includedConnecting Connecting Ethernet CableConnect the Ethernet cable to the network port as shown Connecting Power To connect input and output ports Alarm In/Out Connection DiagramSpeaker Pre-Amp Connecting to Audio Input/OutputMicrophone MicrophonePre-AmpAudio I/O Block Diagram Network connection & setup Network Connection & Setup Setting the IP address Connecting a local PC in the IP router to the cameraConnecting to the camera from an IP router external PC Connecting to the camera from a local PC in the LAN Connecting the camera directly to local area networkingIP Installer screen layout IP InstallerSearching for the camera Click the Manual Set button Setting static ipManual Network Setting Camera listCamera is set to the manually entered IP and is restarted PORTfields, set up port numbersEnter your password Transmission. The default value is 60001TCPIf more than one camera are connected to an IP Router Set the IP and port settings for camera differentlyAutomatic Network Setting Automatic network setting is finishedClick the OK button Dynamic IP Check Setting dynamic ipDynamic IP Setting Examples of using Dynamic IPManual Port Forwarding Port Forwarding Port Mapping Setting사용using the camera Connecting to the cameraConnecting to the camera Checking the Ddns address Connecting to the camera using the IP Installer programIf the following screen appears, click the Install button Installing ActiveXFor Windows XP Service Pack Click the Install ActiveX ControlLogging to the camera Main Screen Layout Using the Viewer ScreenDisplays the recorded video on live screen Print Prints the recorded image on the screenRecord Saves the recorded video as a .avi video file Audio Check the Listen or Speak check box for AudioAt a desired scene, click the Print button To Capture a VideoTo Print a Video Click OKTo stop a recording, click Record button once again At desired scene, click Record button Set up the AVI saveInsufficient Disk Space Setting To Record a VideoThumbnail Size Using the Search Viewer ScreenYou can select the desired time to search the alarm events Name Function and Description DateViewer screen, click the Setup tab Setup window appears Setting upSetting the camera To set up the cameraSetupbasic Setup Screen LayoutBasic Configuration To setup Video/AudioClick Basic  Video & Audio Click Basic  IP To Setup IP settingsClick Basic  User To Setup UsersUser from the Operator and User in the Level field Enter user ID and passwordFor the ID and password, up to Click the Apply buttonWindow, modify User ID Or Level of the user account Click the Apply buttonClick the Delete button in the User window Click Basic  Language To set the display languageClick System  DATE/TIME To set date/timeSetting time is applied To view the log informationClick System  LOG To update the software Software Update window appearsClick System  To reset the system Click System  ResetReset window appears Restart The Reset window appears Click System  Camera To setup the cameraClick Overlay  Layout ConfigurationTo Set text You can display text on the screenClick the Test button Event ConfigurationClick Event  Transfer Setup To set the image transmission functionClick Event  Record Setup To setup the recordClick Event  Alarm Image To set an alarm imageTo set an alarm input Click Event  Alarm Input 1 or Alarm Input Transfer Setup settings Click Event  Motion To set the motion detection functionTo complete the setting, click the Apply button Selected area is colored in yellowSquare box returns to its original color Click Event  Schedule To set scheduled transmissionTo set video streaming Network ConfigurationIf 00166c, and p if To set Ddns부록appendix TroubleshootingBut didn’t trigger an alarm Enabled Motion DetectionFeature under Motion Camera Is it possible to configureDetails SpecificationsFirmware upgrade by web browser Alarm Input TransferSetting IP installation function XP, Vista supportMpeg Frame rate fps Quality Image size Frame rate Resolution LevelFrame Rate Qxga ImageQuality Image size Frame rate Frame Rate UxgaQuality Image size Frame rate Resolution Level108 132 108 Frame Rate SxgaJpeg Lgpl S/W GPL/LGPL Software LicenseAppendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Correct Disposal of This Product AB68-00721E00