Samsung SNC-M300 user manual To reset the system, Click System  Reset

Page 52

To reset the system

If the system abnormally operates or a problem occurs, you can restart or reset the system.

Click <SYSTEM>  <RESET>.

The Reset window appears.

<Restart>: The Reset window appears.

<Factory Default>: Initializes the system settings to the factory settings and then restarts the system.

-<Except Network Parameter>: Initializes the system settings except network settings.

-<All>: Initializes all the system settings. Selecting this option is the same as pressing the [FACTORY RESET] button on the rear panel of the main body.

After reset and restart, you have to connect to the system again.

It takes a few minutes until the system booting is completed.

You cannot connect to the system until the system booting is complete.

After running <Factory Default>  <All>, you have to run <IP Installer.exe> program and setup network settings such as IP address, Subnet mask, Gateway, etc., to connect to the Internet.

48_ Setting Up

Image 52

Contents SNC-M300 Safety precautions Page Important safety instructions Contents Setting Up Using the CameraPrecautions Installation and Use FeaturesPreparation Recommended PC Specifications Compatible PoE SwitchesCompatible IP Routers Checking the components in the packageNames of Each Part FrontRear Description Installation and connection Installing the CameraDisconnect the power cord before installation or relocation When using the CS lensAdjusting the back focus Case of the lens with no zooming functionInserting/Removing an Sdhc Memory Card What is a memory card? Contacts Lock SwitchMemory Card Information not included Selecting a memory card that’s suitable for youConnecting Ethernet Cable ConnectingConnect the Ethernet cable to the network port as shown Connecting Power Alarm In/Out Connection Diagram To connect input and output portsConnecting to Audio Input/Output MicrophoneMicrophonePre-Amp Speaker Pre-AmpAudio I/O Block Diagram Network connection & setup Network Connection & Setup Connecting a local PC in the IP router to the camera Setting the IP addressConnecting to the camera from an IP router external PC Connecting the camera directly to local area networking Connecting to the camera from a local PC in the LANIP Installer IP Installer screen layoutSearching for the camera Setting static ip Manual Network SettingCamera list Click the Manual Set buttonPORTfields, set up port numbers Enter your passwordTransmission. The default value is 60001TCP Camera is set to the manually entered IP and is restartedSet the IP and port settings for camera differently If more than one camera are connected to an IP RouterAutomatic network setting is finished Automatic Network SettingClick the OK button Setting dynamic ip Dynamic IP SettingExamples of using Dynamic IP Dynamic IP CheckPort Forwarding Port Mapping Setting Manual Port ForwardingConnecting to the camera 사용using the cameraConnecting to the camera Connecting to the camera using the IP Installer program Checking the Ddns addressInstalling ActiveX For Windows XP Service PackClick the Install ActiveX Control If the following screen appears, click the Install buttonLogging to the camera Using the Viewer Screen Main Screen LayoutPrint Prints the recorded image on the screen Record Saves the recorded video as a .avi video fileAudio Check the Listen or Speak check box for Audio Displays the recorded video on live screenTo Capture a Video To Print a VideoClick OK At a desired scene, click the Print buttonAt desired scene, click Record button Set up the AVI save Insufficient Disk Space SettingTo Record a Video To stop a recording, click Record button once againUsing the Search Viewer Screen You can select the desired time to search the alarm eventsName Function and Description Date Thumbnail SizeSetting up Setting the cameraTo set up the camera Viewer screen, click the Setup tab Setup window appearsSetup Screen Layout SetupbasicTo setup Video/Audio Basic ConfigurationClick Basic  Video & Audio To Setup IP settings Click Basic  IPTo Setup Users Click Basic  UserEnter user ID and password For the ID and password, up toClick the Apply button User from the Operator and User in the Level fieldOr Level of the user account Click the Apply button Window, modify User IDClick the Delete button in the User window To set the display language Click Basic  LanguageTo set date/time Click System  DATE/TIMETo view the log information Setting time is appliedClick System  LOG Software Update window appears To update the softwareClick System  Click System  Reset To reset the systemReset window appears Restart The Reset window appears To setup the camera Click System  CameraLayout Configuration To Set textYou can display text on the screen Click Overlay Event Configuration Click Event  Transfer SetupTo set the image transmission function Click the Test buttonTo setup the record Click Event  Record SetupTo set an alarm image Click Event  Alarm ImageClick Event  Alarm Input 1 or Alarm Input To set an alarm input Transfer Setup settings To set the motion detection function Click Event  MotionSelected area is colored in yellow To complete the setting, click the Apply buttonSquare box returns to its original color To set scheduled transmission Click Event  ScheduleNetwork Configuration To set video streamingTo set Ddns If 00166c, and p ifTroubleshooting 부록appendixEnabled Motion Detection Feature under MotionCamera Is it possible to configure But didn’t trigger an alarmSpecifications DetailsAlarm Input Transfer SettingIP installation function XP, Vista support Firmware upgrade by web browserQuality Image size Frame rate Resolution Level Frame Rate QxgaImage Mpeg Frame rate fpsFrame Rate Uxga Quality Image size Frame rateLevel Quality Image size Frame rate Resolution108 Frame Rate Sxga 132 108Jpeg GPL/LGPL Software License Lgpl S/WAppendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Appendix Correct Disposal of This Product AB68-00721E00