Moxa Technologies 2310 user manual Reset Button, VDC Power Adaptor

Page 13

VPort 2310 User’s Manual

Introduction

Reset Button

A recessed RESET button is provided for restoring the system to the factory default settings. When the system fails to install properly, or operates abnormally, use the wrench included in the package to reset the system back to its original status. The procedure is as follows:

Step 1: Insert the wrench into the hole to press down on the reset button, which is located about 1.5 cm inside the surface of the casing.

Step 2: While keeping the reset button pressed, restart the system by powering off and on.

Step 3: The system will perform POST twice rather than the once. You can verify this by observing the flashing “CONNECT” and “SERIAL” LEDs.

Step 4: After the system flashes the LEDs for the second time, withdraw the wrench to release the button. The system will now be restored to the factory default settings.

12 VDC Power Adaptor

Connect the power jack of the included power adaptor. Connecting the power adaptor should be the last step involved in the Video Server hardware installation.

1-7

Image 13

Contents First Edition, January Moxa VPort 2310 Video Server User’s ManualCopyright Notice VPort 2310 User’s ManualTrademarks DisclaimerImportant Note Before getting startedTable of Contents Chapter Upgrading System Firmware Page Introduction Overview Product Features Package ChecklistTechnical support for developers Product Description Typical ApplicationFront Panel BNC video inputNetwork and Status LEDs Rear Panel10/100 Mbps Ethernet port RS-232 COM portDI+ General I/O terminal blockVDC Power Adaptor Reset ButtonGetting Started Before Getting Started Hardware InstallationAssigning an IP Address Dhcp Server EnvironmentUsing IP Reporter Non-DHCP Server Environment Assigning the IP Address Manually Mounting VPortPanel Mounting DIN-Rail MountingFunctions Featured NPort’s Homepage Accessing VPort 2310 for the First TimeAuthentication Accessing VPortOpening Your Browser Installing the Plug-in Application Functions Featured on VPort’s Homepage Client Settings Custom PTZ Camera CommandsRelay Output Control Motorized PTZ Camera ControlPage System Configuration Via Web Access System ConfigurationSystem System Configuration Via Web AccessHost name Date and Time Security Root passwordAdd user Manage user$ Reset network at next boot Reset network at next bootReset network at next boot NetworkSmtp GeneralSave the modification Audio ControlChannel port Improve audio quality in a low bandwidth environmentDdns & UPnP Checkmark Enable DdnsDynamic DNS Universal PnP VideoText on Video ColorModulation SizeMaximum Frame Rate Video Quality ControlImage Setting Enable Motion DetectionSave the settings Flip and MirrorEnable Motion Detection box How to Set up a VMD conditionMotion Detection VPort 2310 User’s Manual System Configuration Application Step Setup the General Step Event operation Sequential modeSetup the Trigger Condition Setup the Trigger actionEvent operation Weekly scheduleTrigger output alarm Sequential ModeCamera Control Send Snapshot by Email or FTPPreset Position Interface modeBaud rate bps Select Camera driverCustom commands Focus Focus near, Focus Far actions Custom Camera SettingsLogo figure Homepage LayoutLogo link Background graphView parameters View log fileFactory default System Configuration Via FTPFrom 12 to -12, GMT + Value Video Server Initial Configuration fileCurrent Language, read-only Or 1024 to VPort 2310 User’s Manual System Configuration Values64k, 128k, 256k, 384k, 512k, 768k 1000k, 1200k Telnet Commands System Configuration Via TelnetSystem core debugging Reset network Skip installation at next bootRestore factory default settings Reset systemAdvanced Applications URL Commands for System MaintenanceCapturing Up-to-date Still Images This problemVideo Embedded in Customers’ Homepage Getting snapshot via URLCustomizing Homepage Graphics Download Event-triggered SnapshotsGetting triggered snapshots via URL Getting triggered snapshots via FTPDrive digital outputs URL Commands for DI/DO & Camera’s Actions SettingMoving motorized camera in PTZ direction Recalling camera positionSending commands to devices attached to the COM port URL Commands for System MaintenanceRestore Factory Default Settings via URL Download System Log via FTPUpgrading System Firmware Using Upgrade Wizard to Upgrade Firmware VPort 2310 User’s Manual Upgrading System Firmware Using FTP to Upgrade FirmwareTroubleshooting Frequently Asked Questions Power On Self Test PostLED pattern after Post Failed function Troubleshooting VPort 2310 User’s Manual Troubleshooting VPort 2310 User’s Manual Troubleshooting Homepage name Referenced URL URL Commands of Video ServerName Value Description Resource name Reference URLNetwork configuration URL Video configuration URL Image quality configuration URL Custom camera configuration URL Homepage layout configuration URL Camera model Baud rate Data bits Stop bit Parity bit Settings of Supported PTZ CamerasCamera Control Cable Time Zone Table VPort 2310 User’s Manual Time Zone Table Technology Technical SpecificationsNetwork Serial PortWarranty Power RequirementsAlarm Features Remote Firmware UpgradeService Information Following services are provided Moxa Internet ServicesMoxa Product & VPort Serial Number Problem Report FormProduct Return Procedure