Moxa Technologies 2310 System Configuration Via Telnet, Telnet Commands, System core debugging

Page 53

VPort 2310 User’s Manual		System Configuration

		string with maximum of 60 characters
	DOWN
		string with maximum of 60 characters
	LEFT
		string with maximum of 60 characters
	RIGHT
		string with maximum of 60 characters
	TELESCOPE
		string with maximum of 60 characters
	WIDE
		string with maximum of 60 characters
	NEAR
		string with maximum of 60 characters
	FAR
		string with maximum of 60 characters

	[ALERT]
	<application mode >
	0	disabled, 1 for Sequential, 10 for motion
		detection event, 12 for DI event
	<upload method>
	0	FTP, 1 for email
	<file with time suffix>
	YES	or NO
	<seconds to snapshot after event>
	0	0 ~ 999
	<seconds delay before next event>
	0	0 ~ 999
	<seconds to snapshot periodically>
	0	0 ~ 999
	<time to start snapshot>
	00:00:00	24 hours format
	<time to stop snapshot>
	00:00:00	24 hours format

	[FEATURE]
	<event>
	1

System Configuration Via Telnet

Telnet Commands

Video Server has a Telnet daemon that allows administrators to access some seldom used functions. Using any general terminal program to connect to Video Server will prompt the user for a password. The Username is not requested since only administrators can access the Telnet daemon. The password is the same as that used for web access. After logging in, type “help” for the command list. If “debug” or “dinote” is not executed, Telnet will disconnect automatically after being idle for 1 minute.

System core debugging

General activities are recorded into SYSTEM.LOG continuously, but information about abnormal

4-29

Image 53

Contents First Edition, January Moxa VPort 2310 Video Server User’s ManualCopyright Notice VPort 2310 User’s ManualTrademarks DisclaimerImportant Note Before getting startedTable of Contents Chapter Upgrading System Firmware Page Introduction Overview Technical support for developers Package ChecklistProduct Features Product Description Typical ApplicationFront Panel BNC video inputNetwork and Status LEDs Rear Panel10/100 Mbps Ethernet port RS-232 COM portDI+ General I/O terminal blockVDC Power Adaptor Reset ButtonGetting Started Before Getting Started Hardware InstallationAssigning an IP Address Dhcp Server EnvironmentUsing IP Reporter Non-DHCP Server Environment Assigning the IP Address Manually Mounting VPortPanel Mounting DIN-Rail MountingFunctions Featured NPort’s Homepage Accessing VPort 2310 for the First TimeOpening Your Browser Accessing VPortAuthentication Installing the Plug-in Application Functions Featured on VPort’s Homepage Client Settings Custom PTZ Camera CommandsRelay Output Control Motorized PTZ Camera ControlPage System Configuration Via Web Access System ConfigurationHost name System Configuration Via Web AccessSystem Date and Time Security Root passwordAdd user Manage user$ Reset network at next boot Reset network at next bootReset network at next boot NetworkSmtp GeneralSave the modification Audio ControlChannel port Improve audio quality in a low bandwidth environmentDynamic DNS Checkmark Enable DdnsDdns & UPnP Universal PnP VideoText on Video ColorModulation SizeMaximum Frame Rate Video Quality ControlImage Setting Enable Motion DetectionSave the settings Flip and MirrorMotion Detection How to Set up a VMD conditionEnable Motion Detection box VPort 2310 User’s Manual System Configuration Application Step Setup the General Step Event operation Sequential modeSetup the Trigger Condition Setup the Trigger actionEvent operation Weekly scheduleTrigger output alarm Sequential ModeCamera Control Send Snapshot by Email or FTPPreset Position Interface modeBaud rate bps Select Camera driverCustom commands Focus Focus near, Focus Far actions Custom Camera SettingsLogo figure Homepage LayoutLogo link Background graphView parameters View log fileFactory default System Configuration Via FTPFrom 12 to -12, GMT + Value Video Server Initial Configuration fileCurrent Language, read-only Or 1024 to VPort 2310 User’s Manual System Configuration Values64k, 128k, 256k, 384k, 512k, 768k 1000k, 1200k System core debugging System Configuration Via TelnetTelnet Commands Reset network Skip installation at next bootRestore factory default settings Reset systemAdvanced Applications URL Commands for System MaintenanceCapturing Up-to-date Still Images This problemVideo Embedded in Customers’ Homepage Getting snapshot via URLCustomizing Homepage Graphics Download Event-triggered SnapshotsGetting triggered snapshots via URL Getting triggered snapshots via FTPDrive digital outputs URL Commands for DI/DO & Camera’s Actions SettingMoving motorized camera in PTZ direction Recalling camera positionSending commands to devices attached to the COM port URL Commands for System MaintenanceRestore Factory Default Settings via URL Download System Log via FTPUpgrading System Firmware Using Upgrade Wizard to Upgrade Firmware VPort 2310 User’s Manual Upgrading System Firmware Using FTP to Upgrade FirmwareTroubleshooting LED pattern after Post Failed function Troubleshooting Power On Self Test PostFrequently Asked Questions VPort 2310 User’s Manual Troubleshooting VPort 2310 User’s Manual Troubleshooting Homepage name Referenced URL URL Commands of Video ServerName Value Description Resource name Reference URLNetwork configuration URL Video configuration URL Image quality configuration URL Custom camera configuration URL Homepage layout configuration URL Camera model Baud rate Data bits Stop bit Parity bit Settings of Supported PTZ CamerasCamera Control Cable Time Zone Table VPort 2310 User’s Manual Time Zone Table Technology Technical SpecificationsNetwork Serial PortWarranty Power RequirementsAlarm Features Remote Firmware UpgradeService Information Following services are provided Moxa Internet ServicesMoxa Product & VPort Serial Number Problem Report FormProduct Return Procedure