Jensen vm9311ts instruction manual ASP Audio Sound Processing Config Menu, Screen Calibration

1.Press and hold the DISP button (5) until the clock flashes in the LCD display.

1.Press the /\ or V buttons (18, 19) on the joystick to move the cursor to the “Hour” or “Min” position.

2.Press the < or > buttons (16, 17) on the joystick to adjust the hour or minutes.

3.Press the DISP button (5) on the unit to confirm setup.

Returning to the System Setup Menu

To return to the System Setup menu, move to “BACK”, then press the >/ button (18) on the remote control.

ASP (Audio Sound Processing) Config Menu

The ASP Config Menu allows you to make fine audio adjustments.

Accessing the ASP Config Menu

To access the “ASP CONFIG” Menu from the “SYSTEM SETUP” menu, press the direction buttons on the joystick (16, 17, 18, 19) or remote control (14, 17, 18, 19, 22) to highlight “ASP CONFIG” in green. Press the >/ button (18) on the remote control to enter the “ASP CONFIG” menu. A menu appears with the option for the first item, “Bass Center Freq”, highlighted in light blue.

ASP CONFIG	BACK
	60Hz
	15kHz
Sub Filter	80Hz
Sub Phase	0D
	1.5

Adjusting a Feature

1.Enter the option field for the feature you want to adjust by pressing the >/ button (18) on the remote or by pressing the ENTER (joystick) button (20) on the unit. A submenu appears in a second row with the selected option highlighted in light blue.

2.Select a new value by pressing the >> or << buttons (14, 22) on the remote control or the /\ or V buttons (18, 19) on the joystick.

3.Confirm your selection by pressing the <<, <<, or >> buttons (22, 17, 19) on the remote control, or the < or >

VM9311TS

button (16, 17) on the joystick. The new value is highlighted in light blue and setup is complete.

Table 6: ASP Config Menu Features

Setting	Options	Function
Bass Center	60Hz	According to the audio source, select
Freq		the Bass Center Frequency to
	80Hz
		achieve the best Bass effect.
	100Hz
	130Hz
	150Hz
	200Hz
Treble Center	10KHz	According to the audio source, select
Freq		the Treble Center Frequency to
	12.5KHz
		achieve the best Treble effect.
	15KHz
	17KHz
Sub.W Filter	80Hz	Selecting a crossover frequency sets
		a cut-off frequency of the subwoofer's
	120Hz
		LPF (low-pass filter) and the
	160Hz	“SMALL” speakers' HPF (high-pass
		filter). The Crossover frequency set-
		ting has no effect if the subwoofer is
		set to “OFF” and any other speaker is
		set to “LARGE”.
Sub.W Phase	0D	Subwoofer output IN phase
	180D	Subwoofer output OUT OF phase
		NOTE: Depending on your installa-
		tion, reversing the subwoofer phase
		may increase Bass output.
Bass Q-Factor	1.0	When the Bass Center Frequency is
		selected, adjusting the Bass Q-Fac-
	1.25
		tor alters the sharpness of the Bass
	1.5	output.
	2.0
BACK		Return to previous menu.

Screen Calibration

To access the “Screen Calibration” function from the SYSTEM SETUP menu, press “SCREEN CAL”.

After entering calibration mode, a crosshair appears in a corner quadrant of the screen. To begin calibration, press and hold the crosshair for one second until it moves to the next quadrant. Continue for each quadrant until the calibration is completed.

Exiting the System Setup Menu

To exit setup mode and resume normal playback, press the SYS SETUP button (31) on the remote control or the DISP button (5) on the front panel.

14