Panasonic NV-FJ710 Series operating instructions Linked Timer Recordings with a Digital Receiver

Page 19
Adhesive tape
Erasure prevention tab

To Prevent Accidental Erasure of Recorded Contents

When you record again onto a previously recorded video cassette, the previous recording is automatically erased and replaced with the new recording.

Therefore, to prevent accidental erasure of the recorded contents, break out the erasure prevention

tab after recording.

Use a screwdriver or similar tool to break out the tab.

To Record Again onto the Video Cassette with a Broken Out Erasure Prevention Tab:

If you insert a video cassette with a

broken out erasure prevention tab and press the REC button J, the “1” indication flashes on the VCR display to indicate that recording is not possible.

In this case, cover the tab hole with two layers of adhesive tape.

The adhesive tape substitutes for the prevention erasure tab and makes it possible to record again on this cassette.

To Select the Recording Duration

and Perform Timer Recording

(OTR Recording)

OTR means One-Touch Recording and is called this way, because you can start recording and select the recording duration by repeatedly pressing a single button. This is very convenient, for example when you want to start recording immediately but need to go out or want to go to bed.

After the selected recording duration has elapsed, recording stops and the VCR automatically switches off.

To Perform an OTR Recording:

1Display the VCR picture on the TV.

Linked Timer Recordings with a Digital Receiver

When the AV2 socket of this VCR is connected by a 21-pin cable to a Digital Receiver, it is possible to have timer recordings for a Digital Receiver execute automatically simply by switching the Digital Receiver into timer standby mode and then switching this VCR into timer recording standby mode.

≥Note that linked timer recordings may not work properly with some Digital Receivers.

1Make sure that “AV2” is set to “TIMER”. (See page 50.)

2Insert a video cassette with an intact erasure prevention tab into the VCR.

3Switch the Digital Receiver over to the timer standby mode.

4Press the TIMER REC button D to switch the VCR over to the timer recording standby mode.

≥This VCR does not require any further special timer recording operations.

≥The recording will start at the date and time programmed for the Digital Receiver.

Notes:

≥Always connect the Digital Receiver to be used for timer recordings to the AV2 socket of this VCR using a 21-pin cable.

≥Linked timer recordings are not counted in the total time of timer recording programmings.

≥Make sure that the date and time of the linked timer recording does not conflict with that of a VCR. If programmed recordings do overlap, either linked timer recording or timer recording of VCR have the priority.

Recording

2Insert a video cassette with an intact erasure prevention tab.

3Press the Channel buttons N to select the programme position on which the TV programme to be recorded will be broadcast.

4Press the REC/OTR button c to start recording.

5Press the REC/OTR button c repeatedly to select the desired recording duration.

≥Every time you press this button, the recording duration indicated in the VCR display changes in the following order.

≥For example, if you select “30”, the VCR records a programme from that moment on for 30 minutes.

Counter display

 

30

60

 

(normal recording mode)

(min.)

(min.)

 

240

180

 

120

 

(min.)

(min.)

 

(min.)

 

To Stop the OTR Recording Before the End:

 

Press the Stop button 9.

 

 

 

 

Note:

 

 

 

 

≥ This function also works during Direct TV Recording.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents NV-FJ710 Series Dear Customer ContentsH ij Controls and ComponentsTo Activate the Child Lock Function To Cancel the Child Lock FunctionVCR Operation Numeric buttonsUse Checking the Accessories/Preparing the Remote ControlBefore Avoid humidity and dust Avoid sudden changes in temperatureKeep the VCR away from high temperatures Cleaning the VCRDo not Remove Outer Cover Before UseRemarks TV Operation Setting the Remote Control to Operate Your TVManufacturer Code List of TVs Compatible with the VCR’s Remote ControlHints Connecting SettingOr Method Tuned Correctly by the Auto Setup Function Auto Setup FunctionTo Confirm that the TV Stations Have Been ≥ If you select Schweiz If you want to cancel the Cassette Number Check midway When You Insert a Video CassetteSetting Up When inserting a cassette that was recorded on this VCRTo Play back S-VHS Cassette Tape SQPBuS-VHS Quasi Playback PlaybackConvenient Automatic Functions To Play Back a Recorded Part RepeatedlyTo Display the Approximate Remaining Tape Time RecordingTo Select the Desired Tape Speed To Pause RecordingTo Prevent Accidental Erasure of Recorded Contents Linked Timer Recordings with a Digital ReceiverRecording To Manually Adjust the Audio Recording Level Mode Timer RecordingTo Suspend the Timer Recording Standby To Programme with the On Screen Display OSDPress the OK button T again to conclude Settings To Suspend the Timer Recording Standby ModeTo Programme with ShowView Function To Activate the Auto SP/LP Change Function Other Timer Recordings and Convenient FunctionsTimer Setting the Recording Date/DaysTo Check the Contents of Timer Recording Programmings Programming a Timer Recording of a Satellite ProgrammeTo Change a Timer Recording Programming To Cancel the Programming of a Timer Recording Timer RecordingTo Check the Total Timer Recording Programming Time How to Read the Tape Library Contents Precautions for RecordingTape Library System Tape To Check the Tape Library DataTo Check on Which Cassette a Desired Programme Is Recorded Desired programme title Tape Library System To Manually Enter or Editing a Title or CategoryPress the OK button T again if you are sure that you To Demonstrate the Tape Library System To Restore Deleted Tape Library DataOperation To Cancel the Index Search or to Stop PlaybackTo Cancel the Intro-Jet Scan or to Stop Playback Search FunctionsAssemble Editing EditingAdvanced Operations To Change the Recording Time Album FunctionAudio Dubbing General Audio Dubbing on a Panasonic Hi-Fi VCRTo Connect the VCR to a Stereo Amplifier VCR ModeTV Mode To Connect the VCR to a DecoderHow to install the satellite receiver Preparation To select SAT 19 Enter To Prepare the Satellite ReceiverStandby Typ Action Yes To select SAT 9 EnterTo Enter or Change the Name of a TV Station Various SettingsChannel TV Channel Indication Germany/Italy Other Countries To Preset Pay TV StationsList of TV Reception Channels To Change the Channel Number of an Already Tuned TV StationTo Change the Subtitle Teletext Page Number Subtitles To Change the Type of Video System Colour TV systemTo Change the Title Teletext Page Number Title Various Settings To Restart the Download To Manually Adjust the Clock Setting the VCR’s ClockTo Activate the Automatic Time Correction Function Settings for the Main Menu Item Display Other Convenient Functions Various SettingsPress the Menu button U to display the Main menu on To Set the Playback Picture Sharpness Sharper or Softer Settings for the Main Menu Item FunctionsTo Set the Audio Mode to Be Used During Playback To Set the Remote Control ModeCountry Setting Language SettingVPS Video Programme System/ PDC Programme Delivery Control GlossaryNicam Broadcasting System NV-FJ710EC/ECM/ECY Series Crystal View Control CVC Link FunctionPin Scart Socket √ Playback Does Not Work Properly Before Requesting Service√ On Screen Display Messages √ The VCR Does Not Work Correctly√ The Tape Library System Does Not Work Correctly √ The Remote Control Does Not Work Correctly√ Recording Is Not Possible or Does Not Work Properly √ The Satellite Receiver Cannot Be Controlled CorrectlyTo Return to Auto Tracking Adjusting the Playback PictureIf the Still Picture Scrolls Up or Down V-Lock Adjustment PrecautionsSpecifications
Top Page Image Contents