Panasonic NV-FJ710 Series Link Function, Crystal View Control CVC, Pin Scart Socket

Q Link Function

This function works only if the VCR is connected via a fully- wired 21-pin Scart cable to a TV featuring the Q Link or similar function.

Q Link offers the following functions:

(1)Download from the TV

When you connect the VCR to a TV, the station list data is automatically copied from the TV to the VCR, and the TV stations are assigned to the programme positions on the VCR in the same order as on the TV.

(2)Direct TV Recording

By simply pressing the DIRECT TV REC button 6, you can at once record the same programme that you are watching on the TV.

°(3) TV/VCR Auto Power On

Even if the TV and the VCR are off (standby mode), pressing the Play I, SHOW VIEW L or PROG./CHECK button < automatically turns on both the TV and the VCR.

≥When a cassette with a broken erasure prevention tab is in the VCR, it turns on and starts playback. The TV also turns on.

°(4) VCR Auto Power Off

When you turn the TV off, the VCR is turned off as well. However, this function only works during rewinding, in the stop mode, or when no cassette is inserted.

If the VCR receives the Auto Power Off command while it is rewinding the tape, it turns off after the rewinding has been finished.

This function does not work during the following operations:

Preset Download, Auto Setup, Auto Clock Setting and Manual Tuning.

°(5) On Screen Display Messages

When you are watching a TV programme, the following VCR messages appear on the TV screen to inform you of the VCR’s condition:

Message	Message appears when:
This programme has	A timer recording has just started.
already started
Set VCR to timer	The VCR is not in the timer standby
standby mode	mode 10 minutes before the
	programmed recording start time of a
	timer recording (message appears
	every minute during these
	10 minutes).
VCR is in timer	The VCR-ON/OFF 1, Play I,
standby mode	EJECT Z or LIBRARY button M was
	pressed, although the VCR is in the
	timer standby mode.
VCR is in timer	The VCR-ON/OFF 1, Stop 9, REC/
recording mode	OTR c, Pause/Still d (Pause/Slow
	7), SHOW VIEW L, AUDIO ? or
	SUBTITLE button O was pressed
	while the VCR is in the timer
	recording mode.

≥Depending on the type of TV used, the above messages may not appear correctly.

°The operations marked with asterisk are only available if the VCR is connected to a TV featuring the Q Link or the DATA LOGIC function.

Note:

≥If “Power save” is set to “ON”, the Q Link functions do not work when the VCR is switched off (standby mode).

Crystal View Control (CVC)

The crystal view control function ensures that you always obtain the optimum picture quality so that you get the best picture automatically.

While the VCR is turned on, the CVC indication a is always displayed to show that the Crystal View Control is activated.

21-pin Scart Socket

The 21-pin Scart socket transmits both input and output signals for picture and sound. TVs equipped with the same type of socket can be connected here.

This type of socket is also called Peritel, Euro Connector and Euro AV.

13 5 7 9 11 13 15 17 19 21

2 4 6 8 10 12 14 16 18 20

AV1 Scart Socket (for Q Link connection)

1	Audio output CH2 (R)	12	No connection
2	Audio input CH2 (R)	13	Red ground
3	Audio output CH1 (L)	14	Blanking ground
4	Audio ground	15	Red
5	Blue ground	16	Blanking
6	Audio input CH1 (L)	17	Video output ground
7	Blue	18	Video input ground
8	Switching voltage	19	Video output
9	Green ground	20	Video input
10	Q Link data	21	Ground
11	Green
AV2 Scart Socket
1	Audio output CH2 (R)	12	Reserved
2	Audio input CH2 (R)	13	Red ground
3	Audio output CH1 (L)	14	Blanking ground
4	Audio ground	15	Red
5	Blue ground	16	Blanking
6	Audio input CH1 (L)	17	Video output ground
7	Blue	18	Video input ground
8	Switching voltage	19	Video output
9	Green ground	20	Video input
10	Control signal	21	Ground
11	Green

The Red, Green and Blue (RGB) video signals are looped through only from an external source unit, for example from a connected a pay-TV decoder, i.e. they are not from tape playback.

54