Crown XTI 6002, XTI 2002, XTI 4002 Get Started, Factory Preset #5 Subsynth, Ensure Proper Cooling

Page 6

XTi2 Series Power Ampliﬁers

Get Started

Factory Preset #5: SUBSYNTH

Putting the ampliﬁer in SUBSYNTH mode allows you to turn on the SubHarmonic Synth feature for use with a subwoofer on both channels. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) ﬁlter is enabled on both Channel 1 and Channel 2, and the SubHarmonic Synth feature is turned on at +12dB level. The XTi2 Series ampliﬁers come pre-loaded with a preset that makes it easy to conﬁgure the ampliﬁer for this operation.

Before you get started ensure that you:

1.Connect signal source to Channel 1 and Channel 2 using XLR connectors (the ampliﬁer inputs will automatically be summed together when

selecting this preset).

2. Connector the speaker as shown.

a. Connect a speaker to each channel output using Speakon©, Banana Plugs, or bare wire

Follow these quick steps to conﬁgure the ampliﬁer for SUBSYNTH operation:

1.Push the “Set/Enter” button and you will see the word “Preset” ﬂashing.

2.Push the “Set/Enter” button again to enter the list of presets in the ampliﬁer.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “SUBSYNTH”.

4.Push the “Set/Enter” button to conﬁrm your selection.

5.The display will now read “SUBSYNTH” with the Y icon and XOV icon highlighted.

Ensure Proper Cooling

When using an equipment rack, mount units directly on top of each other. Close any open spaces in rack with blank panels. DO NOT block front or rear air vents. The side walls of the rack should be a minimum of two inches (5.1 cm) away from the ampliﬁer sides, and the back of the rack should be open.

CAUTION: Before you begin installing your ampliﬁer, make sure it is disconnected from the power source, with the power switch in the “off” position and all level controls turned completely down (counterclockwise).

page 6

Operation Manual

Image 6

Contents XTi Some models may be exported under the name AmcronImportant Safety Instructions XTi2 Series ampliﬁers require Class 2 output wiringDeclaration of Conformity Factory Preset #2 Bridge Get StartedStereo DSP Off Factory Preset #3 Xover Factory Preset #4 BRG SubsEnsure Proper Cooling Factory Preset #5 SubsynthGet Started Before you get started ensure that youNext Generation Features include How to Use This ManualWelcome Front Panel Features IndicatorsBack Panel Features XTi 1002, 2002XTi Front Panel Navigation Menu TreeNavigating the LCD Screen Menu Basics Integrated Processing Features Front Panel Lock-Out Advanced Thermal ControlAdvanced Monitoring /PSNBM &BSMZ VMM4QFFEXTi2 Serie Bedienungsanleitung Inbetriebnahme Stereo DSP AUSWerksvoreinstellung Nr Brücke Werksvoreinstellung Nr Xover Werksvoreinstellung Nr BRG SubsStellen Sie eine korrekte Kühlung sicher InbetriebnahmeWerksvoreinstellung Nr Subsynth Bevor Sie beginnen, stellen Sie sicher, dass SieVerwendung dieser Bedienungsanleitung Die Features der nächsten GenerationWillkommen Die Sie und die Welt bewegtFeatures der Vorderseite Features der Rückseite Navigation auf der Vorderseite Navigation durch das Menü des LCD-Bildschirms GrundlagenMenübaum Ausgangsmodus Integrierte VerarbeitungsfunktionenEingangsmodus EqualizingSperre der Tasten der Vorderseite /PSNBM 7PSFJUJH ÚdituesfibimSerie XTi2 Manual de Operación Algunos modelos pueden ser exportados bajo el nombre AmcronCómo empezar Preajuste de fábrica núm Bridge PuentePreajuste de fábrica núm BRG Subs SUB-BAJOS Puenteados Preajuste de fábrica núm Xover Divisor DE FrecuenciaPreajuste de fábrica núm Subsynth Sintetizador subarmónico Cómo empezarCompruebe que existe una ventilación correcta Antes de empezar, debe asegurarse deBienvenido Las funciones de nueva generación sonCómo usar el presente manual Funciones del panel frontal Funciones del panel posterior Navegación del panel frontal Menú de opcionesFunciones de procesamiento integradas Controles avanzados Limitador PeakX PlusControl térmico avanzado Bloqueo del panel frontalManuel d’utilisation de la série XTi2 Certains modèles peuvent être exportés sous le nom d’AmcronStéréo DSP mode Off CommencezPréréglage usine #2 Bridge Préréglage usine #3 Xover Préréglage usine #4 BRG SubsVériﬁer le fonctionnement du refroidissement CommencezPréréglage usine #5 Subsynth Avant de commencer, assurez-vousComment utiliser ce manuel BienvenueLes caractéristiques nouvelle génération comprennent PEQ pour une personnalisation du fonctionnementCaractéristique panneau avant Prises de sortie 4 pôles Speakon Caractéristiques panneau arrièreVentilateurs Connecteur USB HiQnetFonctionnalités panneau avant MenuNaviguer dans le menu de lécran LCD Pour commencer Caractéristiques de traitement intégrées Mode dentréeMode de sortie ÉgalisationCommande perfectionnée Contrôle thermique perfectionnéVerrouillage panneau avant Dimensions. Width, Height, Depth behind mounting surface XTi2 SpecificationsWeight PerformanceUS and Canada Service ServiceWorldwide Service Service at a US or Canada Service Center Factory ServicePayment of Non-Warranty Repairs Packing InstructionsEstimate Approval Warranty United States & Canada Summary of WarrantyWarranty Worldwide Except USA & Canada This page Intentionally Left Blank Crown Audio, Inc IT8000, CDi1000, PCC16XTi2 Series Power Ampliﬁers Card # Exp. date *Card ID # Crown Audio Factory Service InformationType of credit card MasterCard Visa American Express Name on credit card Billing address of credit card