Crown XTI 4002, XTI 2002, XTI 6002, XTI 1002 Factory Preset #3 Xover, Factory Preset #4 BRG Subs

Page 5

XTi2 Series Power Amplifiers

Get Started

Factory Preset #3: XOVER

Putting the amplifier in XOVER mode enables a 1.2kHz 4th order (24dB/octave) filter that sends frequencies of 1.2kHz and below to Channel 1 output and frequencies of 1.2kHz and above to Channel 2 output. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation.

Before you get started ensure that you:

1.Connect signal source to Channel 1 ONLY using an XLR connector (the amplifier inputs will automatically be put into Y mode when selecting this preset).

2.Connector the speaker as shown.

HIGH 2+/–

LOW 1+/–

a. Connect the speaker you wish to receive the low and mid frequencies (1.2kHz and below) to Channel 1 output using Speakon®, Banana Plugs, or bare wire.

b. Connect the speaker you wish to receive the high frequencies (1.2kHz and above) to Channel 2 output using Speakon®, Banana Plugs, or bare wire.

Follow these quick steps to configure the amplifier for XOVER operation:

1.Push the “Set/Enter” button and you will see the word “Preset” flashing.

2.Push the “Set/Enter” button again to enter the list of presets in the amplifier.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “BIAMP”.

4.Push the “Set/Enter” button to confirm your selection.

5.The display will now read “BIAMP” with the Y icon and XOV icon highlighted.

Factory Preset #4: BRG SUBS

Putting the amplifier in BRG SUBS (bridged subs) mode allows you to bridge the amplifier for use with a single 8 or 4 ohm subwoofer. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) LowPass filter is enabled, and the output mode is put into bridge-mono mode. The XTi2 Series amplifiers come pre-loaded with a preset that makes it easy to configure the amplifier for this operation.

Before you get started ensure that you:

1.Connect signal source to Channel 1 and Channel 2 using XLR connectors (the amplifier inputs will automatically be summed together

when selecting this preset).

2. Connector the speaker as shown.

a. If using the binding post outputs, connect the positive terminal of the

speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2.

b. If using a Speakon® connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only.

Follow these quick steps to configure the amplifier for XOVER operation:

1.Push the “Set/Enter” button and you will see the word “Preset” flashing.

2.Push the “Set/Enter” button again to enter the list of presets in the amplifier.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “XOVER”.

4.Push the “Set/Enter” button to confirm your selection.

5.The display will now read “XOVER” with the Y icon and XOV icon highlighted.

Operation Manual

page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Some models may be exported under the name Amcron XTiXTi2 Series amplifiers require Class 2 output wiring Important Safety InstructionsDeclaration of Conformity Stereo DSP Off Factory Preset #2 BridgeGet Started Factory Preset #4 BRG Subs Factory Preset #3 XoverGet Started Factory Preset #5 SubsynthEnsure Proper Cooling Before you get started ensure that youWelcome Next Generation Features includeHow to Use This Manual Indicators Front Panel FeaturesXTi Back Panel FeaturesXTi 1002, 2002 Navigating the LCD Screen Menu Basics Front Panel NavigationMenu Tree Integrated Processing Features Advanced Monitoring Advanced Thermal ControlFront Panel Lock-Out  /PSNBM  &BSMZ  VMM4QFFEXTi2 Serie Bedienungsanleitung Werksvoreinstellung Nr Brücke InbetriebnahmeStereo DSP AUS Werksvoreinstellung Nr BRG Subs Werksvoreinstellung Nr XoverWerksvoreinstellung Nr Subsynth InbetriebnahmeStellen Sie eine korrekte Kühlung sicher Bevor Sie beginnen, stellen Sie sicher, dass SieWillkommen Die Features der nächsten GenerationVerwendung dieser Bedienungsanleitung Die Sie und die Welt bewegtFeatures der Vorderseite Features der Rückseite Menübaum Navigation auf der VorderseiteNavigation durch das Menü des LCD-Bildschirms Grundlagen Eingangsmodus Integrierte VerarbeitungsfunktionenAusgangsmodus Equalizing /PSNBM  7PSFJUJH  Údituesfibim Sperre der Tasten der VorderseiteAlgunos modelos pueden ser exportados bajo el nombre Amcron Serie XTi2 Manual de OperaciónPreajuste de fábrica núm Bridge Puente Cómo empezarPreajuste de fábrica núm Xover Divisor DE Frecuencia Preajuste de fábrica núm BRG Subs SUB-BAJOS PuenteadosCompruebe que existe una ventilación correcta Cómo empezarPreajuste de fábrica núm Subsynth Sintetizador subarmónico Antes de empezar, debe asegurarse deCómo usar el presente manual BienvenidoLas funciones de nueva generación son Funciones del panel frontal Funciones del panel posterior Menú de opciones Navegación del panel frontalFunciones de procesamiento integradas Control térmico avanzado Limitador PeakX PlusControles avanzados Bloqueo del panel frontalCertains modèles peuvent être exportés sous le nom d’Amcron Manuel d’utilisation de la série XTi2Préréglage usine #2 Bridge Stéréo DSP mode OffCommencez Préréglage usine #4 BRG Subs Préréglage usine #3 XoverPréréglage usine #5 Subsynth CommencezVérifier le fonctionnement du refroidissement Avant de commencer, assurez-vousLes caractéristiques nouvelle génération comprennent BienvenueComment utiliser ce manuel PEQ pour une personnalisation du fonctionnementCaractéristique panneau avant Ventilateurs Caractéristiques panneau arrièrePrises de sortie 4 pôles Speakon Connecteur USB HiQnetNaviguer dans le menu de lécran LCD Pour commencer Fonctionnalités panneau avantMenu Mode de sortie Mode dentréeCaractéristiques de traitement intégrées ÉgalisationVerrouillage panneau avant Commande perfectionnéeContrôle thermique perfectionné Weight XTi2 SpecificationsDimensions. Width, Height, Depth behind mounting surface PerformanceWorldwide Service ServiceUS and Canada Service Service at a US or Canada Service Center Factory ServiceEstimate Approval Payment of Non-Warranty RepairsPacking Instructions Summary of Warranty Warranty United States & CanadaWarranty Worldwide Except USA & Canada This page Intentionally Left Blank IT8000, CDi1000, PCC16 Crown Audio, IncXTi2 Series Power Amplifiers Type of credit card MasterCard Visa American Express Crown Audio Factory Service InformationCard # Exp. date *Card ID # Name on credit card Billing address of credit card
Top Page Image Contents