Pioneer PRS-D1200M owner manual Two Amplifier Ex. Bridge

Page 12

Connecting the Unit

Two Amplifier (Ex. Bridge)

 

 

 

 

 

 

Connect to a car stereo.

MODE SELECT switch must

 

 

 

 

 

 

For details, see the

 

 

SYNC OUT

“Connection Diagram”.

be in MASTER position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 Ω to 16 Ω

MODE SELECT switch must be in SYNC INV position.

 

Connecting wire with RCA

Connecting speaker wire

pin plugs (sold separately).

(sold separately).

 

 

SYNC IN

•Only use speakers having an impedance of 2 Ω to 16 Ω. In addition, in the case of connecting multiple speakers with a bridge, check that the synthetic impedance is at least 2 Ω.

•The setting of the POWER MODE switch varies according to the speaker impedance. Slide the POWER MODE switch to the HI-CURRENT position if the impedance is from 2 Ω to less than 4 Ω, or slide it to the NORMAL position if the impedance is from 4 Ω to 16 Ω. The same setting is used for both amplifiers.

•When switching to the SYNC INV mode, the stopper over the MODE SELECT switch must be removed and you can find SYNC INV switch. Remove the stopper after checking that connections are correct.

Two Amplifier

MODE SELECT switch must be in MASTER position.

 

 

 

Connect to a car stereo.

 

 

 

For details, see the

SYNC OUT

“Connection Diagram”.

 

 

 

 

 

1 Ω to 8 Ω

1 Ω to 8 Ω

Connecting wire with RCA

pin plugs (sold separately).

MODE SELECT switch must be in SYNC position.

SYNC IN

•Use speakers having an impedance from 1 Ω to 8 Ω.

•The setting of the POWER MODE switch varies according to the speaker impedance. See the “Setting the Unit” section for details. The same setting is used for both amplifiers.

11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PRS-D1200M Contents Before Using This ProductInformation to User Visit our websiteAbout This Product Setting the Unit Mode Select Switch Input SwitchPower Mode Switch Gain ControlSetting the Gain properly Gain Control of This UnitConnecting the Unit To prevent damage and/or injuryConnection Diagram System remote control wire sold separatelySpeaker connection instructions Connecting the Power Terminal Battery Wire and Ground Wire SizeConnecting the Speaker Output Terminals Using the Speaker InputConnections when using the speaker input Connecting the Speaker Wires Single AmplifierSpeaker Connect to a car stereoTwo Amplifier Ex. Bridge Two AmplifierMode Select switch Mode Select switch must be Sync INV positionFour Amplifier Ex. Bridge Must be in Master positionMode Select switch For details, see Connecting wire with Sync in RCA pin plugs sold To 8 ΩFour Amplifier To 8 ΩInstallation To prevent malfunction and/or injuryAttaching the bass boost remote control Example of installation on the floor mat or on the chassisReplacing the top cover Screw Top Cover Tapping-screwsSpecifications Service après-vente pour un produit Pioneer Table des matièresAvant d’utiliser cet appareil Etats-UnisVisitez notre site Web Quelques mots concernant cet appareilCommande de l’accentua- tion des graves Réglage de l’appareilTémoin ’alimentation Sélecteur infrasonoreCommutateur Mode Select Commande du gainCommande de la fréquence de coupure pour LPF Commutateur Power ModeCommande du gain de cet appareil Réglage correct du gainRaccordement de l’appareil Pour éviter toute anomalie ou blessureSchéma de raccordement Fusible 40 a ⋅’allumage Raccordement de la borne d’alimentation De masseUtilisation de l’entrée de haut-parleur Raccordement des bornes de sortie vers les haut-parleursConnexion lors de l’utilisation de l’entrée de haut-parleur Connexion des câbles des haut-parleurs Amplificateur uniqueDeux amplificateurs Doit être sur la position MasterLe commutateur Mode Select La section Schéma deRaccordement À 16 ΩQuatre amplificateurs Doit être sur la position SyncÀ 8 Ω Doit être sur la position Sync ’installez pas l’appareil Pour éviter toute anomalie de fonctionnement ou blessureFixation de la télécommande d’accentuation des graves Remise en place du couvercle supérieurCaractéristiques techniques Contenido Antes de usar este productoServicio posventa para productos Pioneer EE.UUVisite nuestro sitio Web Sobre este productoAjuste de esta unidad Control de refuerzo de gravesCubierta superior Interruptor selector subsónicoInterruptor Mode Select Interruptor Power ModeControl de ganancia Control de frecuencia de corte para LPFConfiguración apropiada de la ganancia Control de ganancia de esta unidadConexión de la unidad Para evitar daños y/o lesionesDiagrama de conexión Instrucciones de conexión de laToma Sync Output / Sync Terminal de salida de altavozConexiones de terminales sin soldadura Conexión del terminal de alimentaciónTamaño del cable de batería y cable de puesta a tierra Conexión del terminal de salida de altavoz Uso de la entrada de altavozConexión de los cables de altavoces Amplificador simpleDos amplificadores Puente externo Dos amplificadoresA 8 Ω El interruptor Mode Select De automóvil. Para los Conexión del cable conConexión del cable de altavoz Vendido separadamenteEl interruptor Mode Select Para los detalles, consulte la El interruptor Mode SelectCuatro amplificadores Debe estar en la posición SyncInstalación Para evitar fallas de funcionamiento y/o lesionesRecolocación de la cubierta superior CubiertaEspecificaciones Pioneer Corporation Å„ÛÓ 1-óÓÏÂ, å„ÛÓ-ÍÛ, íÓÍËÓ 153-8654, üÔÓÌËfl

PRS-D1200M specifications

The Pioneer PRS-D1200M is a powerful and versatile monoblock amplifier designed for car audio enthusiasts seeking premium sound performance. With a sleek and compact design, it seamlessly integrates into various vehicle setups, making it an ideal choice for those looking to enhance their in-car audio experience.

One of the standout features of the PRS-D1200M is its impressive power output. This amplifier can deliver up to 1200 watts of maximum power, allowing it to drive subwoofers with ease and produce deep, rich bass that truly enhances music enjoyment. Its RMS power rating stands at 600 watts at a 2-ohm load, ensuring a reliable and consistent performance even during prolonged use.

The PRS-D1200M incorporates advanced technologies to ensure high-quality sound reproduction. One such feature is its Class D amplifier design, which not only boosts efficiency but also minimizes heat generation. This design allows for a smaller and lighter unit, making installation easier while still delivering robust audio performance. Additionally, the amplifier is equipped with a high-pass filter, low-pass filter, and subsonic filter, enabling users to fine-tune the sound output according to their personal preferences and audio setup.

Another key characteristic of the PRS-D1200M is its high-quality build. The sturdy construction of the amplifier ensures durability and can withstand the rigors of automotive applications. The unit also features a sophisticated thermal management system, which helps to prevent overheating and maintains optimal performance levels.

Installation of the PRS-D1200M is made user-friendly with its well-organized layout and clear labeling of input and output connections. The amplifier is compatible with various audio sources, making it a versatile addition to any car audio system. The product also offers adjustable gain control that allows users to optimize the output level based on their specific audio requirements.

In conclusion, the Pioneer PRS-D1200M combines power, performance, and customization options in a compact and durable package. Its advanced features and technologies make it an excellent choice for anyone looking to elevate their car audio system with a reliable monoblock amplifier that delivers exceptional sound quality and powerful bass response. Whether you’re an audiophile or a casual listener, the PRS-D1200M stands out as a top contender in the automotive audio market.
Top Page Image Contents