Pioneer PRS-D1200M Mode Select Switch, Gain Control, Cut Off Frequency Control for LPF

Page 5

MODE SELECT Switch

You can select amplifier’s sync mode from MASTER, SYNC and SYNC INV. Set the MODE SELECT switch to the MASTER position when using one amplifier only. When using synchronously connecting two or more of these amplifiers in combination, set the first amplifier to MASTER, and set the remaining amplifiers to SYNC or SYNC INV according to the manner in which they are connect- ed. The only time the amplifier is switched to the SYNC INV mode is when amplifiers are synchro- nously connected with the ex. bridge.

When switching to the SYNC INV mode, the stopper over the MODE SELECT switch must be removed and you can find SYNC INV switch. Remove the stopper after checking that connections are correct. See the “Connecting the Speaker Wires” section for details on the MODE SELECT switch.

Gain Control

If the sound level is too low, even when the volume of the car stereo used along with this power amplifier is turned up, turn gain control clockwise. If the sound distorts when the vol- ume is turned up, turn the gain control counter-clockwise.

•When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more, adjust level to match the car stereo output level.

•If you hear too much noise when using the speaker input terminals, turn the gain control counter-clockwise.

Cut Off Frequency Control for LPF

You can select a cut off frequency from 40 Hz to 240 Hz.

Input Switch

It is possible to input from a car stereo external output or a car stereo speaker output. Switch the input switch before turning on the power. Since switching the input switch while the power is on can cause a loud noise to be emitted from the speakers, the power is turned off by a protection function. When using an external output, slide the switch to the left. For connection instructions, see the “Connection Diagram” section. When using a speaker out- put, slide the switch to the right. In this case, it is necessary to use the supplied speaker input wire with RCA pin cord. For details, see the “Using the Speaker Input” section.

POWER MODE Switch

When using speakers with synthetic impeadance 2 Ω to 8 Ω, slide the switch to the right (NORMAL). When using speakers with synthetic impeadance from 1 Ω to less than 2 Ω, slide the switch to the left (HI-CURRENT). These settings are only used when using a sin- gle amplifier. See the “Connecting the Speaker Wires” section when combining the use of multiple amplifiers.

If the speaker impedance exceeds 2 Ω (4 Ω when using ex. bridge), although the POWER MODE switch be may set to the HI-CURRENT position, setting to the NORMAL position makes it possible to enjoy high power sound.

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS êìëëäàâ

4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents PRS-D1200M Before Using This Product ContentsAbout This Product Information to UserVisit our website Setting the Unit Input Switch Mode Select SwitchPower Mode Switch Gain ControlGain Control of This Unit Setting the Gain properlyTo prevent damage and/or injury Connecting the UnitSpeaker connection instructions Connection DiagramSystem remote control wire sold separately Battery Wire and Ground Wire Size Connecting the Power TerminalConnections when using the speaker input Connecting the Speaker Output TerminalsUsing the Speaker Input Single Amplifier Connecting the Speaker WiresSpeaker Connect to a car stereoTwo Amplifier Two Amplifier Ex. BridgeMode Select switch must be Sync INV position Mode Select switchFour Amplifier Ex. Bridge Must be in Master positionConnecting wire with Sync in RCA pin plugs sold To 8 Ω Mode Select switch For details, seeFour Amplifier To 8 ΩTo prevent malfunction and/or injury InstallationExample of installation on the floor mat or on the chassis Attaching the bass boost remote controlReplacing the top cover Screw Top Cover Tapping-screwsSpecifications Table des matières Service après-vente pour un produit PioneerAvant d’utiliser cet appareil Etats-UnisQuelques mots concernant cet appareil Visitez notre site WebRéglage de l’appareil Commande de l’accentua- tion des gravesTémoin ’alimentation Sélecteur infrasonoreCommande du gain Commutateur Mode SelectCommande de la fréquence de coupure pour LPF Commutateur Power ModeRéglage correct du gain Commande du gain de cet appareilPour éviter toute anomalie ou blessure Raccordement de l’appareil’allumage Schéma de raccordementFusible 40 a ⋅ De masse Raccordement de la borne d’alimentationConnexion lors de l’utilisation de l’entrée de haut-parleur Utilisation de l’entrée de haut-parleurRaccordement des bornes de sortie vers les haut-parleurs Amplificateur unique Connexion des câbles des haut-parleursDoit être sur la position Master Deux amplificateursLa section Schéma de Le commutateur Mode SelectRaccordement À 16 ΩÀ 8 Ω Doit être sur la position Sync Quatre amplificateursDoit être sur la position Sync Pour éviter toute anomalie de fonctionnement ou blessure ’installez pas l’appareilRemise en place du couvercle supérieur Fixation de la télécommande d’accentuation des gravesCaractéristiques techniques Antes de usar este producto ContenidoServicio posventa para productos Pioneer EE.UUSobre este producto Visite nuestro sitio WebControl de refuerzo de graves Ajuste de esta unidadCubierta superior Interruptor selector subsónicoInterruptor Power Mode Interruptor Mode SelectControl de ganancia Control de frecuencia de corte para LPFControl de ganancia de esta unidad Configuración apropiada de la gananciaPara evitar daños y/o lesiones Conexión de la unidadInstrucciones de conexión de la Diagrama de conexiónToma Sync Output / Sync Terminal de salida de altavozTamaño del cable de batería y cable de puesta a tierra Conexiones de terminales sin soldaduraConexión del terminal de alimentación Uso de la entrada de altavoz Conexión del terminal de salida de altavozAmplificador simple Conexión de los cables de altavocesA 8 Ω Dos amplificadores Puente externoDos amplificadores Conexión del cable con El interruptor Mode Select De automóvil. Para losConexión del cable de altavoz Vendido separadamenteEl interruptor Mode Select El interruptor Mode Select Para los detalles, consulte laCuatro amplificadores Debe estar en la posición SyncPara evitar fallas de funcionamiento y/o lesiones InstalaciónCubierta Recolocación de la cubierta superiorEspecificaciones Å„ÛÓ 1-óÓÏÂ, å„ÛÓ-ÍÛ, íÓÍËÓ 153-8654, üÔÓÌËfl Pioneer Corporation

PRS-D1200M specifications

The Pioneer PRS-D1200M is a powerful and versatile monoblock amplifier designed for car audio enthusiasts seeking premium sound performance. With a sleek and compact design, it seamlessly integrates into various vehicle setups, making it an ideal choice for those looking to enhance their in-car audio experience.

One of the standout features of the PRS-D1200M is its impressive power output. This amplifier can deliver up to 1200 watts of maximum power, allowing it to drive subwoofers with ease and produce deep, rich bass that truly enhances music enjoyment. Its RMS power rating stands at 600 watts at a 2-ohm load, ensuring a reliable and consistent performance even during prolonged use.

The PRS-D1200M incorporates advanced technologies to ensure high-quality sound reproduction. One such feature is its Class D amplifier design, which not only boosts efficiency but also minimizes heat generation. This design allows for a smaller and lighter unit, making installation easier while still delivering robust audio performance. Additionally, the amplifier is equipped with a high-pass filter, low-pass filter, and subsonic filter, enabling users to fine-tune the sound output according to their personal preferences and audio setup.

Another key characteristic of the PRS-D1200M is its high-quality build. The sturdy construction of the amplifier ensures durability and can withstand the rigors of automotive applications. The unit also features a sophisticated thermal management system, which helps to prevent overheating and maintains optimal performance levels.

Installation of the PRS-D1200M is made user-friendly with its well-organized layout and clear labeling of input and output connections. The amplifier is compatible with various audio sources, making it a versatile addition to any car audio system. The product also offers adjustable gain control that allows users to optimize the output level based on their specific audio requirements.

In conclusion, the Pioneer PRS-D1200M combines power, performance, and customization options in a compact and durable package. Its advanced features and technologies make it an excellent choice for anyone looking to elevate their car audio system with a reliable monoblock amplifier that delivers exceptional sound quality and powerful bass response. Whether you’re an audiophile or a casual listener, the PRS-D1200M stands out as a top contender in the automotive audio market.
Top Page Image Contents