Pioneer PRS-D1200M owner manual Connecting the Power Terminal, Battery Wire and Ground Wire Size

Page 9

Solderless Terminal Connections

• Do not connect a cord having an exposed core

wire to the power terminals of this amplifier

(Power terminal, GND terminal, System remote

control terminal). Disconnection or breakage of

the core wire can cause a fire or short-circuit.

• Since the wire will become loose over time, it

must be periodically inspected and tightened as

necessary.

• Do not solder or bind the ends of the twisted

wires.

• Fasten while making sure to not to clamp the

insulating sheath of the wire.

1.Pass the battery wire from the engine compartment to the interior of the vehicle.

•After making all other connections to the amplifier, connect the battery wire terminal of the amplifier to the positive (+) terminal of the battery.

Positive (+)

Engine

Interior of

compartment

the vehicle

terminal

 

 

 

ENGLISH ESPAÑOL

• Use the supplied hexagonal wrench to tighten and

loosen the terminal screw of the amplifier.

Securely fasten the wire with the terminal screw.

However, since excessively tightening the termi-

nal screw of the System remote control has the

risk of damaging the wire, be careful not to tight-

en excessively by observing the status of the wire

when tightening.

Fuse (40 A) ⋅ 2

Insert the O-ring rubber grommet into the vehicle body.

Drill a 13 mm hole into the vehicle body.

DEUTSCH

Connecting the Power Terminal

•We recommend that you use the special red bat- tery and ground wire [RD-228], which is sold separately. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body.

•Recommended wires size (AWG: American Wire Gauge) is as follows. The battery wire and the ground wire must be same size.

•Use a 10 AWG to 20 AWG wire for the system remote control wire.

Battery Wire and Ground Wire Size

Wire Length

less than

less than

less than

 

4.5 m

7.2 m

11.4 m

 

(14 ft. 9 in.)

(23 ft. 7 in.)

(37 ft. 5 in.)

Wire Size

8 AWG

6 AWG

4 AWG

 

 

 

 

2.Connect the wires to the terminal.

•Fix the wires securely with the terminal screws.

System remote

Terminal screws

control terminal

 

 

GND terminal

Power terminal

 

 

Ground wire

Battery wire

System remote control wire

WARNING

Failure to securely fasten the battery wire to the ter- minal using the terminal screws could cause the ter- minal area to overheat and could result in damage and injury including minor burns.

FRANÇAIS ITALIANO NEDERLANDS êìëëäàâ

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents PRS-D1200M Before Using This Product ContentsInformation to User Visit our websiteAbout This Product Setting the Unit Input Switch Mode Select SwitchPower Mode Switch Gain ControlGain Control of This Unit Setting the Gain properlyTo prevent damage and/or injury Connecting the UnitConnection Diagram System remote control wire sold separatelySpeaker connection instructions Battery Wire and Ground Wire Size Connecting the Power TerminalConnecting the Speaker Output Terminals Using the Speaker InputConnections when using the speaker input Single Amplifier Connecting the Speaker WiresSpeaker Connect to a car stereoTwo Amplifier Two Amplifier Ex. BridgeMode Select switch must be Sync INV position Mode Select switchFour Amplifier Ex. Bridge Must be in Master positionConnecting wire with Sync in RCA pin plugs sold To 8 Ω Mode Select switch For details, seeFour Amplifier To 8 ΩTo prevent malfunction and/or injury InstallationExample of installation on the floor mat or on the chassis Attaching the bass boost remote controlReplacing the top cover Screw Top Cover Tapping-screwsSpecifications Table des matières Service après-vente pour un produit PioneerAvant d’utiliser cet appareil Etats-UnisQuelques mots concernant cet appareil Visitez notre site WebRéglage de l’appareil Commande de l’accentua- tion des gravesTémoin ’alimentation Sélecteur infrasonoreCommande du gain Commutateur Mode SelectCommande de la fréquence de coupure pour LPF Commutateur Power ModeRéglage correct du gain Commande du gain de cet appareilPour éviter toute anomalie ou blessure Raccordement de l’appareilSchéma de raccordement Fusible 40 a ⋅’allumage De masse Raccordement de la borne d’alimentationUtilisation de l’entrée de haut-parleur Raccordement des bornes de sortie vers les haut-parleursConnexion lors de l’utilisation de l’entrée de haut-parleur Amplificateur unique Connexion des câbles des haut-parleursDoit être sur la position Master Deux amplificateursLa section Schéma de Le commutateur Mode SelectRaccordement À 16 ΩQuatre amplificateurs Doit être sur la position SyncÀ 8 Ω Doit être sur la position Sync Pour éviter toute anomalie de fonctionnement ou blessure ’installez pas l’appareilRemise en place du couvercle supérieur Fixation de la télécommande d’accentuation des gravesCaractéristiques techniques Antes de usar este producto ContenidoServicio posventa para productos Pioneer EE.UUSobre este producto Visite nuestro sitio WebControl de refuerzo de graves Ajuste de esta unidadCubierta superior Interruptor selector subsónicoInterruptor Power Mode Interruptor Mode SelectControl de ganancia Control de frecuencia de corte para LPFControl de ganancia de esta unidad Configuración apropiada de la gananciaPara evitar daños y/o lesiones Conexión de la unidadInstrucciones de conexión de la Diagrama de conexiónToma Sync Output / Sync Terminal de salida de altavozConexiones de terminales sin soldadura Conexión del terminal de alimentaciónTamaño del cable de batería y cable de puesta a tierra Uso de la entrada de altavoz Conexión del terminal de salida de altavozAmplificador simple Conexión de los cables de altavocesDos amplificadores Puente externo Dos amplificadoresA 8 Ω Conexión del cable con El interruptor Mode Select De automóvil. Para losConexión del cable de altavoz Vendido separadamenteEl interruptor Mode Select El interruptor Mode Select Para los detalles, consulte laCuatro amplificadores Debe estar en la posición SyncPara evitar fallas de funcionamiento y/o lesiones InstalaciónCubierta Recolocación de la cubierta superiorEspecificaciones Å„ÛÓ 1-óÓÏÂ, å„ÛÓ-ÍÛ, íÓÍËÓ 153-8654, üÔÓÌËfl Pioneer Corporation

PRS-D1200M specifications

The Pioneer PRS-D1200M is a powerful and versatile monoblock amplifier designed for car audio enthusiasts seeking premium sound performance. With a sleek and compact design, it seamlessly integrates into various vehicle setups, making it an ideal choice for those looking to enhance their in-car audio experience.

One of the standout features of the PRS-D1200M is its impressive power output. This amplifier can deliver up to 1200 watts of maximum power, allowing it to drive subwoofers with ease and produce deep, rich bass that truly enhances music enjoyment. Its RMS power rating stands at 600 watts at a 2-ohm load, ensuring a reliable and consistent performance even during prolonged use.

The PRS-D1200M incorporates advanced technologies to ensure high-quality sound reproduction. One such feature is its Class D amplifier design, which not only boosts efficiency but also minimizes heat generation. This design allows for a smaller and lighter unit, making installation easier while still delivering robust audio performance. Additionally, the amplifier is equipped with a high-pass filter, low-pass filter, and subsonic filter, enabling users to fine-tune the sound output according to their personal preferences and audio setup.

Another key characteristic of the PRS-D1200M is its high-quality build. The sturdy construction of the amplifier ensures durability and can withstand the rigors of automotive applications. The unit also features a sophisticated thermal management system, which helps to prevent overheating and maintains optimal performance levels.

Installation of the PRS-D1200M is made user-friendly with its well-organized layout and clear labeling of input and output connections. The amplifier is compatible with various audio sources, making it a versatile addition to any car audio system. The product also offers adjustable gain control that allows users to optimize the output level based on their specific audio requirements.

In conclusion, the Pioneer PRS-D1200M combines power, performance, and customization options in a compact and durable package. Its advanced features and technologies make it an excellent choice for anyone looking to elevate their car audio system with a reliable monoblock amplifier that delivers exceptional sound quality and powerful bass response. Whether you’re an audiophile or a casual listener, the PRS-D1200M stands out as a top contender in the automotive audio market.
Top Page Image Contents