Pioneer PRS-D1200M owner manual Installation, To prevent malfunction and/or injury

Page 15

Installation

CAUTION

• Do not install in:

—Places where it could injure the driver or pas- sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s seat.

•Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-cir- cuit.

•Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage.

•Install tapping screws in such a way that the screw tip does not touch any wire. This is impor- tant to prevent wires from being cut by vibration of the car, which can result in fire.

•DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

•To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down.

•Never replace the fuse with one of greater value or rating than the original fuse. Use of an improp- er fuse could result in overheating and smoke and could cause damage to the product and injury including burns.

CAUTION:

To prevent malfunction and/or injury

•To ensure proper heat dissipation of the amplifier, be sure of the following during installation.

—Allow adequate space above the amplifier for proper ventilation.

—Do not cover the amplifier with a floor mat or carpet.

•DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

•Do not install the amplifier on unstable places such as the spare tire board.

•The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location.

•Make temporary connections first and check that the amplifier and the system operate properly.

•After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS êìëëäàâ

14

Page 14 Page 16
Image 15
Page 14 Page 16
Contents PRS-D1200M Before Using This Product ContentsInformation to User Visit our websiteAbout This Product Setting the Unit Gain Control Mode Select SwitchInput Switch Power Mode SwitchGain Control of This Unit Setting the Gain properlyTo prevent damage and/or injury Connecting the UnitConnection Diagram System remote control wire sold separatelySpeaker connection instructions Battery Wire and Ground Wire Size Connecting the Power TerminalConnecting the Speaker Output Terminals Using the Speaker InputConnections when using the speaker input Connect to a car stereo Connecting the Speaker WiresSingle Amplifier SpeakerTwo Amplifier Two Amplifier Ex. BridgeMust be in Master position Mode Select switchMode Select switch must be Sync INV position Four Amplifier Ex. BridgeTo 8 Ω Mode Select switch For details, seeConnecting wire with Sync in RCA pin plugs sold To 8 Ω Four AmplifierTo prevent malfunction and/or injury InstallationScrew Top Cover Tapping-screws Attaching the bass boost remote controlExample of installation on the floor mat or on the chassis Replacing the top coverSpecifications Etats-Unis Service après-vente pour un produit PioneerTable des matières Avant d’utiliser cet appareilQuelques mots concernant cet appareil Visitez notre site WebSélecteur infrasonore Commande de l’accentua- tion des gravesRéglage de l’appareil Témoin ’alimentationCommutateur Power Mode Commutateur Mode SelectCommande du gain Commande de la fréquence de coupure pour LPFRéglage correct du gain Commande du gain de cet appareilPour éviter toute anomalie ou blessure Raccordement de l’appareilSchéma de raccordement Fusible 40 a ⋅’allumage De masse Raccordement de la borne d’alimentationUtilisation de l’entrée de haut-parleur Raccordement des bornes de sortie vers les haut-parleursConnexion lors de l’utilisation de l’entrée de haut-parleur Amplificateur unique Connexion des câbles des haut-parleursDoit être sur la position Master Deux amplificateursÀ 16 Ω Le commutateur Mode SelectLa section Schéma de RaccordementQuatre amplificateurs Doit être sur la position SyncÀ 8 Ω Doit être sur la position Sync Pour éviter toute anomalie de fonctionnement ou blessure ’installez pas l’appareilRemise en place du couvercle supérieur Fixation de la télécommande d’accentuation des gravesCaractéristiques techniques EE.UU ContenidoAntes de usar este producto Servicio posventa para productos PioneerSobre este producto Visite nuestro sitio WebInterruptor selector subsónico Ajuste de esta unidadControl de refuerzo de graves Cubierta superiorControl de frecuencia de corte para LPF Interruptor Mode SelectInterruptor Power Mode Control de gananciaControl de ganancia de esta unidad Configuración apropiada de la gananciaPara evitar daños y/o lesiones Conexión de la unidadTerminal de salida de altavoz Diagrama de conexiónInstrucciones de conexión de la Toma Sync Output / SyncConexiones de terminales sin soldadura Conexión del terminal de alimentaciónTamaño del cable de batería y cable de puesta a tierra Uso de la entrada de altavoz Conexión del terminal de salida de altavozAmplificador simple Conexión de los cables de altavocesDos amplificadores Puente externo Dos amplificadoresA 8 Ω Vendido separadamente El interruptor Mode Select De automóvil. Para losConexión del cable con Conexión del cable de altavozDebe estar en la posición Sync El interruptor Mode Select Para los detalles, consulte laEl interruptor Mode Select Cuatro amplificadoresPara evitar fallas de funcionamiento y/o lesiones InstalaciónCubierta Recolocación de la cubierta superiorEspecificaciones Å„ÛÓ 1-óÓÏÂ, å„ÛÓ-ÍÛ, íÓÍËÓ 153-8654, üÔÓÌËfl Pioneer Corporation

PRS-D1200M specifications

The Pioneer PRS-D1200M is a powerful and versatile monoblock amplifier designed for car audio enthusiasts seeking premium sound performance. With a sleek and compact design, it seamlessly integrates into various vehicle setups, making it an ideal choice for those looking to enhance their in-car audio experience.

One of the standout features of the PRS-D1200M is its impressive power output. This amplifier can deliver up to 1200 watts of maximum power, allowing it to drive subwoofers with ease and produce deep, rich bass that truly enhances music enjoyment. Its RMS power rating stands at 600 watts at a 2-ohm load, ensuring a reliable and consistent performance even during prolonged use.

The PRS-D1200M incorporates advanced technologies to ensure high-quality sound reproduction. One such feature is its Class D amplifier design, which not only boosts efficiency but also minimizes heat generation. This design allows for a smaller and lighter unit, making installation easier while still delivering robust audio performance. Additionally, the amplifier is equipped with a high-pass filter, low-pass filter, and subsonic filter, enabling users to fine-tune the sound output according to their personal preferences and audio setup.

Another key characteristic of the PRS-D1200M is its high-quality build. The sturdy construction of the amplifier ensures durability and can withstand the rigors of automotive applications. The unit also features a sophisticated thermal management system, which helps to prevent overheating and maintains optimal performance levels.

Installation of the PRS-D1200M is made user-friendly with its well-organized layout and clear labeling of input and output connections. The amplifier is compatible with various audio sources, making it a versatile addition to any car audio system. The product also offers adjustable gain control that allows users to optimize the output level based on their specific audio requirements.

In conclusion, the Pioneer PRS-D1200M combines power, performance, and customization options in a compact and durable package. Its advanced features and technologies make it an excellent choice for anyone looking to elevate their car audio system with a reliable monoblock amplifier that delivers exceptional sound quality and powerful bass response. Whether you’re an audiophile or a casual listener, the PRS-D1200M stands out as a top contender in the automotive audio market.
Top Page Image Contents