Axis Communications M7014 user manual Media Streams, How to Stream H.264, Axis Media Control AMC

Page 11

AXIS M7014 Video Encoder

Media Streams

Media Streams

The Axis product provides several video stream formats. Your requirements and the properties of your network will determine the type you use.

The Live View page in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream profiles. Other applications and clients can access video streams directly, without going via the Live View page.

How to Stream H.264

The video compression standard H.264 makes good use of bandwidth, and can provide high quality video streams at less than 1 Mbit/s.

Deciding which combination of protocols and methods to use depends on your viewing requirements, and on the properties of your network. The available options in AXIS Media Control are:

Unicast RTP

This unicast method (RTP over UDP) is used

 

 

for live unicast video, especially when it is

 

 

important to always have an up-to-date video

 

 

stream, even if some images are dropped.

Unicasting is used for video-on-demand

 

 

transmission so that there is no video traffic

RTP over RTSP

This unicast method (RTP tunneled over RTSP)

on the network until a client connects and

 

is useful as it is relatively simple to configure

 

requests the stream.

 

firewalls to allow RTSP traffic.

 

Note that there are a maximum of 20

 

 

RTP over RTSP over HTTP

This unicast method can be used to traverse

simultaneous unicast connections.

 

firewalls. Firewalls are commonly configured to

 

 

allow the HTTP protocol, thus allowing RTP to

 

 

be tunneled.

 

 

 

 

Multicast RTP

This method (RTP over UDP) should be used for live multicast video. The video stream is always

 

up-to-date, even if some images are dropped.

 

 

Multicasting provides the most efficient usage of bandwidth when there are large numbers of

 

clients viewing simultaneously. A multicast cannot however, pass a network router unless the

 

router is configured to allow this. It is not possible to multicast over the Internet, for example.

 

Note also that all multicast viewers count as one unicast viewer in the maximum total of 20

 

simultaneous connections.

 

 

 

 

AXIS Media Control negotiates with the Axis product to determine the transport protocol to use. The order of priority, listed in the AMC Control Panel, can be changed and the options disabled, to suit specific requirements.

Note

H.264 is licensed technology. The Axis product includes one H.264 viewing client license. Installing additional unlicensed copies of the client is prohibited. To purchase additional licenses, contact your Axis reseller.

MJPEG

This format uses standard JPEG still images for the video stream. These images are then displayed and updated at a rate sufficient to create a stream that shows constantly updated motion.

The Motion JPEG stream uses considerable amounts of bandwidth, but provides excellent image quality and access to every image contained in the stream. The recommended method of accessing Motion JPEG live video from the Axis product is to use the AXIS Media Control in Internet Explorer in Windows.

AXIS Media Control (AMC)

AXIS Media Control (AMC) in Internet Explorer in Windows is the recommended method of accessing live video from the Axis product.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Axis M7014 Video Encoder Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis M7014 Video Encoder Table of ContentsHardware Overview Connectors and ButtonsHardware Overview Color Indication LED IndicatorsSD Card Slot Control ButtonAccess from a Browser Accessing the ProductAccessing the Product Click Use Https Accessing the Product Access from the InternetSet the Root Password Network TCP/IP AdvancedPTZ Controls Live ViewControls on the Live View Axis Media Control viewer toolbarPreset Positions, on Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Axis M7014 Video Encoder Basic Setup Setting Up the ProductSetting Up the Product Pixel Counter VideoVideo Video Stream264 Quad streamImage Image Appearance Camera SettingsImage Settings Video Stream ProfilesGo to Video Overlay Image Video OverlayOverlay Image Go to Video Video Stream and select the Image tabGo to Events Action Rules Using Overlay Text in an Action RulePrivacy Mask Default live view video Live View ConfigLive View Config Browser Viewer Description Default Viewer for BrowsersViewer Settings User Defined LinksPTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomLimits Device SettingsPTZ Pan Tilt Zoom Guard Tour AdvancedOSD Menu Installing a PTZ driverMotion Detection DetectorsDetectors Camera TamperingParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionRecommended values Default valuesMedium level 50% Low level 0%Events EventsGo to Events Action Rules and click Add Setting Up an Action RulePTZ Control Go to Events Recipients and click Add Setting Up an Email RecipientEvents Recipients Recipient Use with actionGo to Events Recurrences and click Add SchedulesRecurrences Go to Events Schedules and click AddContinuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityGo to System Options Security Ieee IeeeCertificates Go to System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Axis Internet Dynamic DNS ServiceHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4RTP/H.264 QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMNetwork Share StorageBonjour SD CardSystem Overview MaintenanceSupport Support OverviewFile Upload Plain ConfigLogs & Reports ScriptingSystem Options Reset to Factory Default Settings Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Basic Product is accessible locally but not externallyProblems with streaming H.264 Storage and disk management problems Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsTechnical Specifications Technical SpecificationsConnectors Function Pin RS-485/422 ConnectorPerformance Considerations M3.2

M7014 specifications

The Axis Communications M7014 is a state-of-the-art video encoder designed to enhance the capabilities of existing analog cameras by integrating them into modern IP-based video surveillance systems. This encoder facilitates the transition from traditional surveillance infrastructure to more advanced and flexible IP solutions, making it an ideal choice for organizations looking to modernize their security setups.

One of the main features of the M7014 is its ability to encode video in multiple formats, including H.264 and Motion JPEG. H.264 is particularly valued for its efficient compression capabilities, allowing high-quality video to be transmitted using less bandwidth, which is essential for optimizing storage and network resources. The encoder supports a resolution of up to 720p, ensuring clear and detailed footage that can be crucial for identifying individuals or events.

The M7014 offers four channels, enabling users to connect and manage multiple analog cameras simultaneously. This multi-channel capability is perfect for businesses needing extensive coverage over different areas without the need to invest in multiple encoders. Additionally, the encoder provides two-way audio capabilities, allowing for real-time communication between the monitoring center and the field, which adds an extra layer of security and operational efficiency.

Incorporating advanced video analytics, the M7014 supports functionalities such as motion detection and audio detection, which trigger alerts and notifications in case of suspicious activities. This proactive approach ensures that security personnel are immediately informed about potential threats, enabling timely responses.

Moreover, the M7014 is designed with ease of installation and integration in mind. It features Power over Ethernet (PoE), reducing the need for additional power cables and simplifying the setup process. This technology also allows for remote management and configuration, making it easier for users to monitor and adjust settings from various locations.

Furthermore, the device is equipped with Axis' unique One-Click Cloud capability, which allows for seamless connection to cloud services, enhancing the flexibility and scalability of the surveillance system. The M7014 is also compatible with a variety of video management software, ensuring that users can choose a platform that best meets their operational needs.

In summary, the Axis Communications M7014 is a powerful and versatile video encoder designed to support the transition from analog to IP surveillance. With its multi-channel capabilities, efficient video compression, advanced analytics, and user-friendly features, it represents a valuable addition to any security infrastructure, enhancing surveillance effectiveness while streamlining operations.
Top Page Image Contents