Axis Communications M7014 user manual QoS Quality of Service, UPnPTM, RTP/H.264

Page 40

AXIS M7014 Video Encoder

System Options

QoS (Quality of Service)

QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.

The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark the following types of traffic: live video, event/alarm traffic and management traffic.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 34. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 44.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Axis M7014 Video Encoder About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis M7014 Video EncoderHardware Overview Connectors and ButtonsHardware Overview LED Indicators SD Card SlotControl Button Color IndicationAccessing the Product Accessing the ProductAccess from a Browser Accessing the Product Access from the Internet Set the Root PasswordNetwork TCP/IP Advanced Click Use HttpsLive View Controls on the Live ViewAxis Media Control viewer toolbar PTZ ControlsPreset Positions, on How to Stream H.264 Media StreamsMedia Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream Axis M7014 Video Encoder Setting Up the Product Setting Up the ProductBasic Setup Video VideoVideo Stream Pixel CounterImage Quad stream264 Camera Settings Image SettingsVideo Stream Profiles Image AppearanceVideo Overlay Overlay ImageGo to Video Video Stream and select the Image tab Go to Video Overlay ImagePrivacy Mask Using Overlay Text in an Action RuleGo to Events Action Rules Live View Config Live View ConfigDefault live view video Default Viewer for Browsers Viewer SettingsUser Defined Links Browser Viewer DescriptionPreset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomDevice Settings PTZ Pan Tilt Zoom Guard TourAdvanced LimitsInstalling a PTZ driver OSD MenuDetectors DetectorsCamera Tampering Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersGo to Detectors Motion Detection Parameter Object Size History Sensitivity DescriptionDefault values Medium level 50%Low level 0% Recommended valuesEvents EventsPTZ Control Setting Up an Action RuleGo to Events Action Rules and click Add Setting Up an Email Recipient Events RecipientsRecipient Use with action Go to Events Recipients and click AddSchedules RecurrencesGo to Events Schedules and click Add Go to Events Recurrences and click AddRecordings RecordingsRecording List Continuous RecordingLanguages LanguagesSystem Options System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Basic TCP/IP Settings Date & TimeNetwork Go to System Options Security CertificatesIPv4 Address Configuration IPv6 Address ConfigurationAxis Internet Dynamic DNS Service ARP/PingAdvanced TCP/IP Settings DNS ConfigurationNTP Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 FTPQoS Quality of Service UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Storage BonjourSD Card Network ShareMaintenance SupportSupport Overview System OverviewPlain Config Logs & ReportsScripting File UploadSystem Options Reset to Factory Default Settings Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallyBasic Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalVideo Camera Settings Storage and disk management problemsTechnical Specifications Technical SpecificationsConnectors Performance Considerations RS-485/422 ConnectorFunction Pin M3.2

M7014 specifications

The Axis Communications M7014 is a state-of-the-art video encoder designed to enhance the capabilities of existing analog cameras by integrating them into modern IP-based video surveillance systems. This encoder facilitates the transition from traditional surveillance infrastructure to more advanced and flexible IP solutions, making it an ideal choice for organizations looking to modernize their security setups.

One of the main features of the M7014 is its ability to encode video in multiple formats, including H.264 and Motion JPEG. H.264 is particularly valued for its efficient compression capabilities, allowing high-quality video to be transmitted using less bandwidth, which is essential for optimizing storage and network resources. The encoder supports a resolution of up to 720p, ensuring clear and detailed footage that can be crucial for identifying individuals or events.

The M7014 offers four channels, enabling users to connect and manage multiple analog cameras simultaneously. This multi-channel capability is perfect for businesses needing extensive coverage over different areas without the need to invest in multiple encoders. Additionally, the encoder provides two-way audio capabilities, allowing for real-time communication between the monitoring center and the field, which adds an extra layer of security and operational efficiency.

Incorporating advanced video analytics, the M7014 supports functionalities such as motion detection and audio detection, which trigger alerts and notifications in case of suspicious activities. This proactive approach ensures that security personnel are immediately informed about potential threats, enabling timely responses.

Moreover, the M7014 is designed with ease of installation and integration in mind. It features Power over Ethernet (PoE), reducing the need for additional power cables and simplifying the setup process. This technology also allows for remote management and configuration, making it easier for users to monitor and adjust settings from various locations.

Furthermore, the device is equipped with Axis' unique One-Click Cloud capability, which allows for seamless connection to cloud services, enhancing the flexibility and scalability of the surveillance system. The M7014 is also compatible with a variety of video management software, ensuring that users can choose a platform that best meets their operational needs.

In summary, the Axis Communications M7014 is a powerful and versatile video encoder designed to support the transition from analog to IP surveillance. With its multi-channel capabilities, efficient video compression, advanced analytics, and user-friendly features, it represents a valuable addition to any security infrastructure, enhancing surveillance effectiveness while streamlining operations.
Top Page Image Contents