Axis Communications M7014 user manual Recurrences, Go to Events Schedules and click Add

Page 31

AXIS M7014 Video Encoder

Events

2.Enter a Name and select Email from the Type list.

3.Enter the email addresses to send emails to in the To field. Use commas to separate multiple addresses.

4.Select the email provider from the Provider list.

5.Enter the user ID and password for the email account.

6.Click Test to send a test email.

To set up an email recipient using for example a corporate email server, follow the instructions above but select User defined as Provider. Enter the email address to appear as sender in the From field. Select Advanced settings and specify the SMTP server address, port and authentication method. Optionally, select Use encryption to send emails over an encrypted connection. The server certificate can be validated using the certificates available in the Axis product. For information on how to upload certificates,

see Certificates, on page 35.

Schedules

Schedules can be used as action rule triggers or as additional conditions, for example to record video if motion is detected outside office hours. Use one of the predefined schedules or create a new schedule as described below.

To create a new schedule:

1.Go to Events > Schedules and click Add.

2.Enter a descriptive name and the information needed for a daily, weekly, monthly or yearly schedule.

3.Click OK.

To use the schedule in an Action Rule, select the schedule from the Schedule drop-down list in the Action Rule Setup page.

Recurrences

Recurrences are used to trigger Action Rules repeatedly, for example every 5 minutes or every hour.

To set up a recurrence:

1.Go to Events > Recurrences and click Add.

2.Enter a descriptive name and recurrence pattern.

3.Click OK.

To use the recurrence in an Action Rule, first select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list.

To modify or remove recurrences, select the recurrence in the Recurrences List and click Modify or Remove.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Axis M7014 Video Encoder Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis M7014 Video Encoder Table of ContentsHardware Overview Connectors and ButtonsHardware Overview Color Indication LED IndicatorsSD Card Slot Control ButtonAccessing the Product Accessing the ProductAccess from a Browser Click Use Https Accessing the Product Access from the InternetSet the Root Password Network TCP/IP AdvancedPTZ Controls Live ViewControls on the Live View Axis Media Control viewer toolbarPreset Positions, on Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Axis M7014 Video Encoder Setting Up the Product Setting Up the ProductBasic Setup Pixel Counter VideoVideo Video StreamImage Quad stream264 Image Appearance Camera SettingsImage Settings Video Stream ProfilesGo to Video Overlay Image Video OverlayOverlay Image Go to Video Video Stream and select the Image tabPrivacy Mask Using Overlay Text in an Action RuleGo to Events Action Rules Live View Config Live View ConfigDefault live view video Browser Viewer Description Default Viewer for BrowsersViewer Settings User Defined LinksPTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomLimits Device SettingsPTZ Pan Tilt Zoom Guard Tour AdvancedOSD Menu Installing a PTZ driverMotion Detection DetectorsDetectors Camera TamperingParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionRecommended values Default valuesMedium level 50% Low level 0%Events EventsPTZ Control Setting Up an Action RuleGo to Events Action Rules and click Add Go to Events Recipients and click Add Setting Up an Email RecipientEvents Recipients Recipient Use with actionGo to Events Recurrences and click Add SchedulesRecurrences Go to Events Schedules and click AddContinuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityCertificates IeeeGo to System Options Security Ieee Go to System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Axis Internet Dynamic DNS ServiceHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4RTP/H.264 QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMNetwork Share StorageBonjour SD CardSystem Overview MaintenanceSupport Support OverviewFile Upload Plain ConfigLogs & Reports ScriptingSystem Options Reset to Factory Default Settings Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallyBasic Storage and disk management problems Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsTechnical Specifications Technical SpecificationsConnectors Performance Considerations RS-485/422 ConnectorFunction Pin M3.2

M7014 specifications

The Axis Communications M7014 is a state-of-the-art video encoder designed to enhance the capabilities of existing analog cameras by integrating them into modern IP-based video surveillance systems. This encoder facilitates the transition from traditional surveillance infrastructure to more advanced and flexible IP solutions, making it an ideal choice for organizations looking to modernize their security setups.

One of the main features of the M7014 is its ability to encode video in multiple formats, including H.264 and Motion JPEG. H.264 is particularly valued for its efficient compression capabilities, allowing high-quality video to be transmitted using less bandwidth, which is essential for optimizing storage and network resources. The encoder supports a resolution of up to 720p, ensuring clear and detailed footage that can be crucial for identifying individuals or events.

The M7014 offers four channels, enabling users to connect and manage multiple analog cameras simultaneously. This multi-channel capability is perfect for businesses needing extensive coverage over different areas without the need to invest in multiple encoders. Additionally, the encoder provides two-way audio capabilities, allowing for real-time communication between the monitoring center and the field, which adds an extra layer of security and operational efficiency.

Incorporating advanced video analytics, the M7014 supports functionalities such as motion detection and audio detection, which trigger alerts and notifications in case of suspicious activities. This proactive approach ensures that security personnel are immediately informed about potential threats, enabling timely responses.

Moreover, the M7014 is designed with ease of installation and integration in mind. It features Power over Ethernet (PoE), reducing the need for additional power cables and simplifying the setup process. This technology also allows for remote management and configuration, making it easier for users to monitor and adjust settings from various locations.

Furthermore, the device is equipped with Axis' unique One-Click Cloud capability, which allows for seamless connection to cloud services, enhancing the flexibility and scalability of the surveillance system. The M7014 is also compatible with a variety of video management software, ensuring that users can choose a platform that best meets their operational needs.

In summary, the Axis Communications M7014 is a powerful and versatile video encoder designed to support the transition from analog to IP surveillance. With its multi-channel capabilities, efficient video compression, advanced analytics, and user-friendly features, it represents a valuable addition to any security infrastructure, enhancing surveillance effectiveness while streamlining operations.
Top Page Image Contents