10 Press MUTE/RTN/SETUP to return to the previous screen.
•When the speaker is set to the “OFF” mode, the parametric equalizer for that speaker cannot be set. Refer to “Setting the Speakers” (page 33).
•It is not possible to adjust the frequencies of adjacent bands within 7 steps.
•Check the playable frequency ranges of the connected speakers before making the equalizer adjustments. If the speaker’s playable frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz or 20 Hz band has no effect. Additionally, you may overload and damage the speakers.
•When the parametric EQ is adjusted, the adjustment for graphic EQ becomes ineffective.
Setting Bass Sound Control
1 Check that Defeat mode is off (page 10).
2 Press and hold MUTE/RTN/SETUP for at least 2 seconds.
The SETUP screen is displayed.
3 Press the joystick up or down to select AP SETUP and press the joystick right.
The AP SETUP screen is displayed.
4 Press the joystick up or down to select B.SOUND CNTL, then press the joystick right.
Setting Bass Compressor
You can adjust the sound of low frequencies as desired.
5 Press the joystick up or down to select BASS COMP.
6 Press the joystick left or right to select the desired mode.
Bass sound is emphasized more as the mode is sequentially switched as MODE1 
2 
3, offering you vivid low frequencies.
Select OFF when the setting is not necessary.
Press MUTE/RTN/SETUP to return to the previous screen.
Setting Bass Focus
Using the previously specified delay number (time difference) allows you to set a time difference between the
5 Press the joystick up or down to select the desired speaker.
6 Press the joystick left or right to adjust the front, rear, left and right speakers.
7 Repeat step 5 and 6 to set other speakers.
•Any setting in Bass Focus is applied in time correction, too.
•Press MUTE/RTN/SETUP to return to the previous screen.
Speaker Setup
The
Check the playable frequency range of the speakers (not including the subwoofer) before performing this operation to verify whether the speakers can play low frequencies (of about 80 Hz or less).
•Avoid stopping, pausing, switching the disc, cueing,
1 Check that Defeat mode is off (page 10).
2 Press and hold MUTE/RTN/SETUP for at least 2 seconds.
The SETUP screen is displayed.
3 Press the joystick up or down to select AP SETUP, then press the joystick right.
The AP SETUP screen is displayed.
4 Press the joystick up or down to select SPEAKER SETUP, then press the joystick right.
5 Press the joystick up or down to select the desired speaker.
6 Press the joystick left or right to select the speaker characteristic.
OFF*1: When no speaker is connected.
SMALL: When a speaker that cannot play low frequencies (80 Hz or less) is connected.
LARGE*2: When a speaker that can play low frequencies (80 Hz or less) is connected.
*1 It is not possible to set the front speakers to “OFF”. *2 If the front speakers are set to “SMALL”, the rear and
center speakers cannot be set to “LARGE”.
7 Repeat step 5 and 6 to set each speaker.
•If the center speaker is turned “OFF,” the center channel’s audio signals are added to the audio signals output from the front speakers.
•If you set the speaker response to “OFF,” also set the speaker setting to “OFF” (page 33).
•Perform the setup for all the speakers (“Front,” “Center,” “Rear” and “Subwoofer”). Otherwise, the sound may not be balanced.
•When the center speaker is set to “OFF”, the setting is ineffective even if center is set with this function.
•Through changing the settings on each speaker, a change in the output of the other speakers may occur due to the setting requirements.
•When using PRO LOGIC II, if the rear speaker is set to “LARGE”, there will be no output from the subwoofer.