Alpine VPA-B222 owner manual Connecting the Navigation, Connecting an External Input Device AUX

Page 17

Setting the Interrupt Type of the Speaker

 

Navigation Audio Interruption Volume

Input Voice

 

Adjustment

 

 

 

The following explanation is how to set the voice interrupt type of the speaker input. When the navigation voice guidance is made to interrupt, set to DEMAND, and the telephone voice is made to interrupt, set to MUTE, these are recommended.

Setting items: F.SYS MIX TYP

Setting content: FULL / DEMAND / MUTE

FULL: Regardless of the speaker interruption detection level, voice interruption and source sound are both active. If voice interruption cannot be heard clearly, adjust the source volume accordingly on the commander.

DEMAND: When speaker input interruption occurs, voice interruption may be too high or too low, adjust the source volume so voice interruption can be heard. If no speaker input interruption occurs for 5 seconds, source volume returns to the level you initially set. When speaker input interruption occurs again, source volume level automatically returns to the last one you set.

MUTE: To avoid voice interruption not being heard clearly, this setting mutes the current source sound whenever speaker input interruption occurs. In this setting, even when voice interruption cannot be heard clearly, you can still set the volume by the commander. When speaker input interruption occurs, the commander buttons blink. Press SOURCE/ POWER to cancel voice interruption.

•The setting can be made when INT or BOTH is set in "Setting the Speaker Input Mode" (page 14).

Setting the Channel of the Speaker Interruption Detection

The setting should be made according to the speaker output of the car system (navigation/telephone).

Setting items: F.SYS INT CH.

Setting content: L / R / BOTH

L:Outputs from the left speaker of the car system.

R:Outputs from the right speaker of the car system. BOTH: Outputs from both speakers of the car system.

•Usually set to BOTH.

•The setting can be made when INT or BOTH is set in "Setting the Speaker Input Mode" (page 14).

•The speaker input interrupt voice is output from the right and left front speaker regardless of this setting.

Connecting the Navigation

If an Alpine navigation system is connected, make the necessary settings in “Setting the Navigation/Speaker Input Voice Interruption” (page 14). Also make the following settings.

Setting the Navigation Mode

When you connect optional navigation equipment, set to ON.

Setting item: NAV.

Setting contents: OFF / ON

ON: Navigation source is displayed.

OFF: Navigation source is not displayed. The settings related to the navigation cannot be changed from this unit.

With an Alpine navigation system connected to the VPA-B222, the voice guidance of the navigation system will be mixed with the DVD or CD playback sound.

You can adjust the volume level of the voice guidance.

Setting item: NAV. MIX LV

Setting contents: 0 to 15

•When NAV. is turned on, the setting can be made. Refer to "Setting the Navigation Mode" (page 15).

Connecting an External Input Device (AUX)

If an external input device is connected, make the following settings.

Setting the AUX Mode

Setting item: AUX IN-1, 2, 3

Setting content: OFF / ON

OFF: AUX source is not displayed.

ON: AUX source is displayed.

•When OFF is selected, the settings related to AUX cannot be changed from this unit.

•AUX IN-3 is adjustable when the external expansion box (VPE-S431) is connected.

•OFF is not displayed when a DVD player or DVD changer is connected with the optional Ai-NET.

•When either DVD player or DVD changer is connected to AUX IN 1, DVD is displayed on the screen. When both of them are connected, DVD is displayed for AUX IN 1 and DVD CHANGER is displayed for AUX IN 2.

Naming External Devices

When more than one external device is connected, you can name each (up to 3) as you like.

Setting items: NAME

Setting contents: AUX / VCR / GAME-1,2 / TV / EXTDVD*

•The setting can be made when ON is set in "Setting the AUX Mode" (page 15).

•The selected source name is displayed instead of AUX source name. If selecting TV/EXT.DVD as the source, the screen will change to the function screen of that source.

•Only when an Alpine TV tuner is connected, can you operate the displayed function guide from this unit.

•If an Ai-NET compatible DVD player/DVD changer is connected, names are automatically set, however, they cannot be changed.

*“EXT.DVD” is displayed on the source selection screen when a DVD player is connected, and “DVD-1-3” is displayed on the source selection screen when the NAME setting is set to “EXTDVD” on more than one AUX (included when an external Ai-NET compatible DVD player is connected).

Adjusting the External Input Audio Level

Setting item: LEVEL

Setting content: LOW / HIGH

LOW: Decreases the external input audio level

HIGH: Increases the external input audio level

15-EN

Page 16 Page 18
Image 17
Page 16 Page 18
Contents VPA-B222 CHA-1214CHM-S630 CHA-S634Contents Operating Instructions CD/MP3/WMA Operation Optional Installation Connections Operating Instructions Precautions Turning Power On or Off Feature Accessory ListGetting Started Initial System Start-UpAdjusting the Volume Switching a SourceLowering Volume Quickly RadioAutomatic Memory of Station Presets Manual Storing of Station PresetsTuning to Preset Stations Setting Analog Mode HD Radio mode onlyChanging the Display HD Radio mode only Other Useful FeaturesAdjusting the Audio Press and hold MUTE/RTN/SETUP for at least 2 secondsAdjusting the Fader Adjusting the BalanceSetting the Treble Control Setting the Bass ControlSystem Setup screen is displayed Switching the function of the remote sensorRear Entertainment Function 11-ENGeneral Setup Operation SetupSetting the Time Display Demonstration FunctionSystem Setup Operation Using the Speaker Input Connecting an External Input Device AUX Connecting the NavigationConnecting a Subwoofer Connecting the Rear MonitorSetting the Commander Setting the OthersSetting the Auxiliary Data Field Display Adjusting the display positionCD/MP3/WMA Operation Optional Playing CD/MP3/WMAX. Random Play Folder/File SearchRepeat Play 18-ENRepeat mode is changed When Repeat is displayed Press / /ENTERDVD/Video CD Operation Optional Playing DVD/Video CDTo display the DVD mode screen Playing Still Frames PausingFinding the Beginnings of Chapters or Tracks Fast-forwarding/Fast-reversingSwitching the Audio Tracks Changing Discs only when DVD changer is connectedDisplaying the Top Menu Screen DVD only Stopping Playback PRE StopSwitching from the disc menu Switching the Angle DVD only22-EN Monitor displaySAT Radio Receiver Optional Tuning in to Categorized ProgramsReceiving Channels with the SAT Receiver Changing the DisplayChecking the SAT Radio ID Number Storing Channel PresetsReceiving Stored Channels 24-ENCategory/Channel Search Function IPod OptionalStoring Weather or Traffic information from SAT Radio Receiving Weather or Traffic Information from SAT RadioSearching by Playlist Searching for a desired SongSearching by artist name Searching by album nameRandom Play Shuffle M.I.X Select Playlist/Artist/AlbumSearching by Song Name 27-ENDisplaying the Navigation Screen Navigation System OptionalMap Screen Function Menu Screen FunctionSwitching Audio Automatic Memory of Channel PresetsTV Operation Optional Operating TV UnitOperating Auxiliary Devices Optional Auxiliary Device Optional30-EN External input screen is displayedFactory System Operating Factory System Speaker Input modeHDD Player Operation Optional Listening to Music of HDD32-EN Adjustment Procedure for Dolby SurroundExternal Audio Processor Optional Set MX Mode of the External Audio Processor Setting the SpeakersOver Adjustment AP Setup screen is displayedTo adjust other channels, repeat steps 7 Check that Defeat mode is offPerforming Time Correction Manually TCR 34-ENGraphic Equalizer Adjustments Phase SwitchingParametric Equalizer Adjustments Adjustable level -9 to +9Speaker Setup Setting Bass Sound ControlSetting Bass Compressor Setting Bass FocusAdjusting the acoustic image Setting of Dolby DigitalAchieving powerful high volume sound Adjusting the speaker levelsStoring Settings in the Memory Adjusting the DVD LevelCalling up the Preset Memory Using the Pro Logic II ModeSoft button operation Linear PCM SettingBasic operation 39-EN40-EN Setup OperationRadio Operation 41-EN CD/MP3/WMA OperationDVD/Video CD Operation 42-EN SAT Radio Operation43-EN IPod OperationStored weather or traffic channel is recalled Enters the selected playlist/artist/album/song44-EN TV Operation HDD Player Operation45-EN InformationCase of Difficulty 46-EN Indication for SAT Receiver ModeIndication for iPod Mode 47-EN SpecificationsCommander 48-EN Installation and ConnectionsInstalling the unit InstallationWhen mounting with Velcro fasteners 49-EN50-EN Mounting the CommanderPattern Mount the HolderIf the ACC power supply is not available Connection Diagram of Spst Switch Sold Separately51-EN Parking Brake Lead Connection52-EN Connections VPA-B222 Wiring Diagram53-EN 54-EN System ExampleConnect the Alpine Monitor RCA Extension Cable IncludedRCA Extension Cable Included with DVD video player Guide Control Lead White/Green Ai-NET Connector55-EN 56-EN When Connecting External EquipmentTo AV Selector Terminal To Ai-NET Connector Black To Ai-NET Connector Gray57-EN Connect the car system standard audio system, etc 58-EN
Top Page Image Contents