Sharp SD-AT1000W Connecting speaker wires, Supplied FM aerial, Supplied AM loop aerial

Page 11

"Connecting speaker wires

Make sure to leave the AC power lead disconnected when connecting the speakers.

To prevent accidental short circuit between and terminals, connect the speaker wires to the speakers first then to the unit.

1 Connect the wires to the speakers.

Speaker terminals

Red

Tube

Label

Black

2 Connect the other end to the main unit.

Label

 

 

 

Speaker plug

Plug in with the rising

side facing up.

 

 

 

 

 

 

 

 

 

Caution:

!The supplied speakers are exclusively for SD-AT1000W. Do not connect them to other equipment, and do not connect other speakers to SD- AT1000W. It may cause malfunction.

!Do not mistake the and , and right and left terminals of the speaker leads. (The right speaker is placed on the right when you face the unit.)

!Do not let the bare speaker wires touch each other.

!Do not stand or sit on the speakers. You may be injured.

!Insert the speaker plug fully with the rising side facing up.

!Hold the speaker plug when removing it from the main unit.

Pulling the lead may cause malfunction to the unit.

Incorrect

 

 

 

SD-AT1000W(LAG) TINSZA121AWZZ

Aerial connection

 

 

SD-AT1000W

 

 

 

 

 

 

 

 

ENGLISH

Supplied FM aerial:

 

FM aerial

AM loop

 

 

Connect the FM aerial wire to the FM 75 OHMS

 

 

socket and position the FM aerial wire in the di-

 

aerial

 

 

 

 

 

 

rection where the strongest signal can be re-

 

 

 

 

ceived.

 

 

 

 

 

Supplied AM loop aerial:

 

Black

 

 

 

Connect the AM loop aerial wire to the AM and

 

 

 

 

GND terminals. Position the AM loop aerial for

 

White

 

 

optimum reception. Place the AM loop aerial on

 

 

 

 

 

 

 

a shelf, etc., or attach it to a stand or a wall with

 

 

 

 

screws (not supplied).

 

 

 

 

 

Notes:

 

 

 

 

-

 

 

 

connectionsSystem

connectionSpeaker/ Aerial connection

External FM aerial

 

 

 

! Placing the aerial on the unit or near the AC power lead may cause noise pickup.

 

 

Place the aerial away from the unit for better reception.

 

 

 

! When static is still heard even after adjusting the position of the AM loop aerial, try

 

 

reversing the wire connections.

 

 

 

 

Installing the AM loop aerial:

 

 

 

 

< Assembling >

< Attaching to the wall >

 

 

 

 

Wall

Screws (not supplied)

 

 

External FM or AM aerial:

 

 

 

 

 

Use an external FM or AM aerial if you require better reception. Consult your dealer.

 

 

When using an external AM aerial, be sure to keep the wire of the AM loop aerial

 

 

connected.

 

 

 

 

 

 

External AM aerial

 

 

 

-

 

15 m (49 feet)

 

 

 

 

7.5 m (25 feet)

 

 

 

 

Earth rod

Earth wire

 

 

 

 

 

 

 

 

 

AM loop aerial

3

1

2

3

4

5

6

7

8

E-10

04/7/21

SD-AT1000W_LAG_E2.fm

TINSZA121AWZZ

Image 11
Contents SD-AT1000W Special notes IntroductionContentsGeneral AccessoriesPrecautionsSD-AT1000W Volume controlMain unit front panel Controls and indicatorsIndicators InformationMain unit rear panel Controls Remote controlGeneral Displays the DVD menu Sets the VCR power to on or Stops the cassetteSwitches the input to TV or VCR Selects the DVD menuBass Reflex Duct Woofer Speaker Terminals Front speakerCentre speaker SubwooferCarrying the subwoofer Using antislip speaker cushionsSpeaker functions Speaker connection Supplied AM loop aerial Connecting speaker wiresInstalling the AM loop aerial Supplied FM aerialSystem connections to DVD Audio connections to DVD players, VCRs, TVs, etcConnections Players, VCRs, TVs, etcDVD players, VCRs, TVs, etc Using other subwooferSystem Audio connection to TVs or other equip MentTo set the unit to stand-by mode Connecting the AC power leadAC power lead ConnectingPreparation Setting the AM/FM intervalTo change the AM/FM tuning interval For UseMagnetically shielded speakers System installationPreparation for Use System installation Placing the speaker systemUse Remote controlBattery installation Test of the remote control Use HeadphonesSD-AT1000WGeneral control MutingSetting the clock Basic Operation Listening to the radio Manual or Auto tuningSD-AT1000WListening to the radio To recall a memorised station To erase all the contents of the preset MemoryMemorising a station Listening to the playback sound from DVD players, VCRs, etc Various sounds Audio signal indicators / Speaker indicatorsEnjoying various sounds OperationEnjoying Press the Sound Mode buttonBasic Listening to sounds with multi-channel Ch, etcWhilst the disc is playing, press the Stereo button Press the Sound Mode button to turn the Bass on or Bass OFFListening to 2-channel stereo sounds Adjusting speaker delay/speaker level Adjusting speaker delay/speaker levelAdvanced Features Speaker delay settingSpeaker type Level range Default setting Speaker level settingTo end the speaker setting FL CT FR SW SL SR Readjust the speaker levels if not equalBefore setting timer Timer and sleep operationSetting the timer Turn the power on and press the Timer but- tonAdvanced Features Timer and sleep operation To use timer and sleep operation together Setting the sleep timerReferences Troubleshooting chartTroubleshooting chart Symptom Possible cause ReferenceCleaning the cabinet MaintenanceError indicators and warnings Optional accessorySpecifications SpecificationsSD-AT1000WLAGmemo1 TINSZA121AWZZ SD-AT1000WLAGmemo2 TINSZA121AWZZ Sharp Corporation