Sharp SD-AT1000W operation manual Maintenance, Error indicators and warnings, Optional accessory

Page 32

SD-AT1000W

ENGLISH

References - Maintenance / Error indicators and warnings / Optional accessory -

Troubleshooting chart (continued)

!If trouble occurs

When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction.

If such a problem occurs, do the following:

1Set the unit to the stand-by mode and turn the power on again.

2If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory by resetting it.

Clearing all the memory (reset)

1Unplug the unit.

2Whilst holding down the ON/STAND-BY button, plug in the AC power lead. At this time, the unit will not be turned on.

3Press the ON/STAND-BY button again to turn the power on.

Caution:

This operation will erase all data stored in memory and restore various settings to the initial status (default).

When the protection circuit is activated:

Occasionally at very high volume levels, the protection circuit may be activated to set the unit to the stand-by mode.

Unplug the unit and, after 5 minutes or more, plug it in again. Turn down the volume if set too high.

Maintenance

!Cleaning the cabinet

Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth.

"Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the cabinet finish.

"Do not apply oil to the inside of the equipment as this may cause malfunctions.

Error indicators and warnings

When you fail to perform operations properly, the following messages are displayed on the unit.

Display

Meaning

"Place the unit away from noise source or plug the

AC power lead to another wall socket. (*)

"The cooling fan on the back of the main unit does not

run due to foreign objects caught in it.

Set this unit to the stand-by mode and remove the foreign objects around the fan.

"The digital audio input socket is not connected prop-

erly.

"Turn off the unit and check if the cable is properly connected.

"Unspecified signal is received and cannot be recog- nised.

(*): Should the same message appear even if the unit is unplugged and plugged in or is set to the stand-by mode and on again, contact your local dealer where you pur- chased the unit.

Optional accessory

Use only the specified optional accessory to operate this product properly. For speaker installation, read instructions supplied with stands.

FLOOR SPEAKER

STAND

Model: AD-AT11ST

The appearance of optional accessory may differ from the illustration above.

E-31

04/7/21

SD-AT1000W_LAG_E5.fm

TINSZA121AWZZ

Page 31 Page 33
Image 32
Page 31 Page 33
Contents SD-AT1000W IntroductionContents Special notesAccessories PrecautionsSD-AT1000WVolume control GeneralControls and indicators IndicatorsInformation Main unit front panelMain unit rear panel Controls Remote controlGeneral Sets the VCR power to on or Stops the cassette Switches the input to TV or VCRSelects the DVD menu Displays the DVD menuFront speaker Centre speakerSubwoofer Bass Reflex Duct Woofer Speaker TerminalsCarrying the subwoofer Using antislip speaker cushionsSpeaker functions Speaker connection Connecting speaker wires Installing the AM loop aerialSupplied FM aerial Supplied AM loop aerialAudio connections to DVD players, VCRs, TVs, etc ConnectionsPlayers, VCRs, TVs, etc System connections to DVDUsing other subwoofer SystemAudio connection to TVs or other equip Ment DVD players, VCRs, TVs, etcConnecting the AC power lead AC power leadConnecting To set the unit to stand-by modeSetting the AM/FM interval To change the AM/FM tuning intervalFor Use PreparationSystem installation Preparation for Use System installationPlacing the speaker system Magnetically shielded speakersUse Remote controlBattery installation Test of the remote control Headphones SD-AT1000WGeneral controlMuting UseSetting the clock Basic Operation Listening to the radio Manual or Auto tuningSD-AT1000WListening to the radio To recall a memorised station To erase all the contents of the preset MemoryMemorising a station Listening to the playback sound from DVD players, VCRs, etc Audio signal indicators / Speaker indicators Enjoying various soundsOperation Various soundsPress the Sound Mode button BasicListening to sounds with multi-channel Ch, etc EnjoyingWhilst the disc is playing, press the Stereo button Press the Sound Mode button to turn the Bass on or Bass OFFListening to 2-channel stereo sounds Adjusting speaker delay/speaker level Advanced FeaturesSpeaker delay setting Adjusting speaker delay/speaker levelSpeaker level setting To end the speaker settingFL CT FR SW SL SR Readjust the speaker levels if not equal Speaker type Level range Default settingTimer and sleep operation Setting the timerTurn the power on and press the Timer but- ton Before setting timerAdvanced Features Timer and sleep operation Setting the sleep timer To use timer and sleep operation togetherTroubleshooting chart Troubleshooting chartSymptom Possible cause Reference ReferencesMaintenance Error indicators and warningsOptional accessory Cleaning the cabinetSpecifications SpecificationsSD-AT1000WLAGmemo1 TINSZA121AWZZ SD-AT1000WLAGmemo2 TINSZA121AWZZ Sharp Corporation
Top Page Image Contents