Sharp SD-AT1000W System installation, Placing the speaker system, Magnetically shielded speakers

Page 16

SD-AT1000W

ENGLISH

System installation

Preparation for Use - System installation -

E-15

"Placing the speaker system

The best surround effect will be achieved by placing each speaker at the same distance from the listening position.

It is recommended to arrange the speakers as shown below.

	Front	Centre
	Front	speaker Front
	speaker (left)	speaker (right)
	Subwoofer
		Default setting:
		2 m
	Surround	Surround
	speaker (left)	Surround
	speaker (left)	speaker (right)
		speaker (right)

Note:

The default distance is set to 2 m. If speakers cannot be placed at equal distances, refer to "Speaker delay setting" (see page 25).

Installation image:

The speaker stands are optionally available (see page 31). Refer to their instructions for assembly.

Notes:

!Place the TV halfway between the front speakers.

!It is recommended that the centre speaker be placed near the television.

!Place the surround speakers at a position just above the height of your ears.

!The subwoofer vibrates whilst reproducing bass. Place it on a stable, sturdy sur- face.

!The subwoofer reproduces bass. Place it anywhere you like.

Centre speaker

Same distance		Same distance

Front speaker (left)

Front speaker (right)

"Magnetically shielded speakers

The front, centre and subwoofer speakers may be placed beside or near the TV as they are magnetically shielded. However, discolouration may occur depending on the TV type.

If colour variation occurs...

Turn off the TV (from the power switch).

After 15 - 30 minutes, turn the TV on again.

If the colour variation is still present...

Move the speakers further away from the TV.

Refer to the user's manual of the TV for details.

Note:

The surround speakers are not magnetically shielded.

04/7/21

SD-AT1000W_LAG_E2.fm

TINSZA121AWZZ

Image 16

Contents SD-AT1000W IntroductionContents Special notesAccessories PrecautionsSD-AT1000WVolume control GeneralControls and indicators IndicatorsInformation Main unit front panelMain unit rear panel General Remote controlControls Sets the VCR power to on or Stops the cassette Switches the input to TV or VCRSelects the DVD menu Displays the DVD menuFront speaker Centre speakerSubwoofer Bass Reflex Duct Woofer Speaker TerminalsSpeaker functions Using antislip speaker cushionsCarrying the subwoofer Speaker connection Connecting speaker wires Installing the AM loop aerialSupplied FM aerial Supplied AM loop aerialAudio connections to DVD players, VCRs, TVs, etc ConnectionsPlayers, VCRs, TVs, etc System connections to DVDUsing other subwoofer SystemAudio connection to TVs or other equip Ment DVD players, VCRs, TVs, etcConnecting the AC power lead AC power leadConnecting To set the unit to stand-by modeSetting the AM/FM interval To change the AM/FM tuning intervalFor Use PreparationSystem installation Preparation for Use System installationPlacing the speaker system Magnetically shielded speakersBattery installation Test of the remote control Remote controlUse Headphones SD-AT1000WGeneral controlMuting UseSetting the clock SD-AT1000WListening to the radio Manual or Auto tuningBasic Operation Listening to the radio Memorising a station To erase all the contents of the preset MemoryTo recall a memorised station Listening to the playback sound from DVD players, VCRs, etc Audio signal indicators / Speaker indicators Enjoying various soundsOperation Various soundsPress the Sound Mode button BasicListening to sounds with multi-channel Ch, etc EnjoyingListening to 2-channel stereo sounds Press the Sound Mode button to turn the Bass on or Bass OFFWhilst the disc is playing, press the Stereo button Adjusting speaker delay/speaker level Advanced FeaturesSpeaker delay setting Adjusting speaker delay/speaker levelSpeaker level setting To end the speaker settingFL CT FR SW SL SR Readjust the speaker levels if not equal Speaker type Level range Default settingTimer and sleep operation Setting the timerTurn the power on and press the Timer but- ton Before setting timerAdvanced Features Timer and sleep operation Setting the sleep timer To use timer and sleep operation togetherTroubleshooting chart Troubleshooting chartSymptom Possible cause Reference ReferencesMaintenance Error indicators and warningsOptional accessory Cleaning the cabinetSpecifications SpecificationsSD-AT1000WLAGmemo1 TINSZA121AWZZ SD-AT1000WLAGmemo2 TINSZA121AWZZ Sharp Corporation