VTech LS6425-3, LS6426-3, LS6425-4, LS6426-4, LS6425-2 user manual Battery, Appendix

Page 62

Appendix

Battery

It takes up to 10 hours for the battery to be fully charged. When it is fully charged, you can expect the following performance:

Operation	Operating time
While in handset use (talking*)	Up to seven hours

While in speakerphone mode (talking*)	Up to five hours
While not in use (standby**)	Up to seven days

*Operating times vary depending on your actual use and the age of the battery. **Handset is not charging or in use.

The battery needs charging when:

•A new battery is installed in the handset.

•The handset beeps.

•A battery is properly installed and the screen is blank.

•Low battery or Place in charger displays on the handset screen.

CAUTION:

To reduce the risk of fire or injury, read and follow these instructions:

•Use only the battery(ies) provided or equivalent. To order a replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

•Do not dispose of the battery(ies) in a fire. Check with local waste management codes for special disposal instructions.

•Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

•Exercise care in handling batteries in order not to create a short circuit with conductive materials.

•Charge the battery(ies) provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

•Observe proper polarity orientation between the battery and metallic contacts.

•To prevent fire or shock hazard, do not expose this product to water or any type of moisture.

58

Image 62

Contents Models LS6425/LS6425-2 LS6425-3/ LS6425-4 LS6426-3/LS6426-4 User’s manualw w w.v t e c h p h o n e s . c o m Congratulations Telephone operation Telephone settingsGetting started Multiple handset useAnswering system operation Answering system settingsCaller ID AppendixParts checklist Getting startedTelephone installation Battery installation HANDSET Battery chargingdisplays Place in charger Installation options Tabletop to wall mount installationWall mount to tabletop installation 4. See Telephone installation on pageFIND HANDSET Telephone base layoutIN USE light REPEATCHARGE light Handset layoutVOLUME directory/volume MUTE/DELETEMENU/SELECT CID//VOLUME caller ID/volumeOFF/CANCEL Dialing keysPUSH TO TALK PUSH TO TALK PTTPress to begin a broadcast to one or multiple handsets pages 28 and To enter the handset menu Telephone settingsUsing the menu MENU/SELECT 3. Press MENU/SELECT to select Ringer volume Ringer volume telephone baseRinger volume handset Ringer toneMENU/SELECT 3. Press MENU/SELECT to select LCD language Set date and timeLCD language Voice announce caller ID Clear voicemail indicators Rename handset Key toneCID time synchronization Home area codeDial mode WebsiteMake a call Listening volumeTelephone operation Predial a callTemporary tone dialing MuteTemporary ringer silencing Equalizer Find handsetCall waiting RedialCopy a number from the redial list to the directory Review and dial a redial entryDelete a redial entry OR 1. Press /FLASH or /SPEAKER 2. Press REDIAL/PAUSETo access a number from the redial list while on a call To access a number from the directory while on a callTo access a number from the caller ID log while on a call Chain dialingIntercom Multiple handset useJoin a call in progress To share an outside callAnswer an incoming call during an intercom call Announced transferBlind transfer press OFF/CANCEL on your handsetTurn PTT on or off PTT requires two handsets when you press PUSH TO TALKPush-to-talk PTT PTT to a single handset PTT to multiple handsets Answer a PTT call Change a one-to-one PTT call to intercom callMake an outgoing call during a PTT call End a PTT callAnswer an incoming call during a PTT call To end or leave a PTT callDirectory About the directoryENTER NAME Mike Smith Add a directory entryAnswering sys Directory Review Add contact ENTER NUMBER Dial a directory entry Search the directoryAlphabetical search Mike Smith EDIT NUMBER EDIT NAME Mike Smith Saved Edit a directory entryDelete a directory entry Mike Smith Mike Smith Delete contact?Copy from Directory Assign a directory entry to a speed dial locationDial a speed dial entry 5. Press MENU/SELECT to choose Change SD Reassign a speed dial numberDelete a speed dial entry Information about caller ID with call waiting Caller IDAbout caller ID Caller ID log Memory matchView dialing options Missed call indicatorReview the caller ID log displays EDIT NUMBER Dial a caller ID log entrySave a caller ID log entry to the directory To delete one entry Delete the caller ID log entriesCaller ID log display screen messages To delete all entriesAnnouncement Answering system settingsAnswering system Record your own announcement3. Press MENU/SELECT to highlight Announcement Play your announcementDelete your announcement 4. Press MENU/SELECT to select Play anncTo turn on or off with the telephone base Answer on/offCall screening To turn on or off with a handsetRemote access code Number of ringsMessage alert tone Message recording timeAnswering system and voicemail Using the answering system and voicemail togetherAnswering system operation Call intercept Message capacityNew message indication Call screening at the telephone baseMessage playback To play messages with the telephone basePlay old msgs, then press MENU/SELECT To play messages with a handsetPlay new msgs it announces, “Less than three minutes to record.”“All old messages deleted.” Delete all old messagesTo delete all old messages with the telephone base To delete all old messages with a handsetTo record a memo Record, play and delete memosMessage window displays Command Remote access3. Then you can enter one of the following remote commands 1. Dial your telephone number from any touch-tone telephoneAppendix Handset display screen messagesNo battery is installed. Follow the directions for battery Telephone base lights Handset and telephone base indicatorsHandset lights ANS ON/OFFBattery To register a handset Expand your telephone systemAdd and register a handset To deregister all handsets To resetDeregister handsets There is no dial tone TroubleshootingMy telephone does not work at all I cannot dial out from my cordless handsetThe CHARGE light is off Low battery shows on screenThe telephone does not ring when there is an incoming call My handset beeps and is not performing normally I hear noise on the cordless handset and the keys do not workThe other party cannot hear my voice during a call I hear other calls when using the cordless handsetMy caller ID features are not working properly Registration failed appears on the handsetNew voicemail and show on the display and I don’t know why Caller ID entries do not match the numbers I need to dialOut of range OR No pwr at base shows in the handset screen I cannot retrieve voicemail messagesThe messages on the answering system are very difficult to hear The outgoing announcement is not clearThe answering system does not record messages The messages on the answering system are incompleteThe answering system does not respond to remote commands Common cure for electronic equipmentImportant safety instructions SAVE THESE INSTRUCTIONSOperating range Precautions for users of implanted cardiac pacemakersMaintenance Cleaning your telephoneAbout cordless telephones The RBRC sealFCC Part 68 and ACTA FCC, ACTA and IC regulationsFCC Part Industry Canada How long is the limited warranty period? Limited warrantyWhat does this limited warranty cover? What is not covered by this limited warranty?What must you return with the Product to get warranty service? Please retain your original sales receipt as proof of purchaseHow do you get warranty service? Other limitationsTechnical specifications Index Index