Sharp DK-KP95PH Troubleshooting chart, Headphones, IPod, iPhone or iPad, CD player, Tuner

Enhancing your system (continued)

■Listening to the playback sounds of portable audio player, etc.

1Use a connection lead to connect the portable audio player etc. to the AUDIO IN socket. When using video equipment, connect the audio output to this unit and the video output to a television.

2Press the ON/STAND-BY button to turn the power on.

3Press the AUDIO IN button on the remote control or FUNCTION button repeatedly on main unit to select AUDIO IN function.

4Play the connected equipment. If volume level of the connected device is too high, sound distortion may occur. Should this happen, lower the volume of the connected device. If volume level is too low, increase the volume of the connected device.

Note:

To prevent noise interference, place the unit away from the television.

■Headphones

●Do not turn the volume on to full at switch on and listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss.

●Before plugging in or unplugging the headphone, reduce the volume.

●Be sure your headphone has a 3.5 mm (1/8") diameter plug and impedance between 16 and 50 ohms. The recommended impedance is 32 ohms.

●Plugging in the headphone disconnects the speakers automatically. Adjust the volume using the VOLUME control.

Troubleshooting chart

Many potential problems can be resolved by the owner without calling a service technician.

If something is wrong with this product, check the following before calling your authorised SHARP dealer or service centre.

■General

Symptom	Possible cause
● The clock is not set	● Did a power failure occur?
to the correct time.	Reset the clock. (Refer
	page 6)
● When a button is	● Set the unit to the power
pressed, the unit	stand-by mode and then
does not respond.	turn it back on.
	● If the unit still malfunctions,
	reset it. (Refer page 21)
● No sound is heard.	● Is the volume level set to
	“Min”?
	● Are the headphones
	connected?

■iPod, iPhone or iPad

Symptom	Possible cause
● No sound is	● The iPod, iPhone or iPad is
produced.	not playing.
	● The iPod, iPhone or iPad is
	not properly connected to
	the unit.
	● Is the AC power lead of the
	unit plugged in?
● iPod, iPhone or	● The iPod, iPhone or iPad is
iPad will not	not making full contact with
charge.	the connector.
	● Using iPod (3rd generation).
	● The iPod or iPhone is not
	supported. Refer to page 9
	for compatible models.
● “This accessory is	● The iPhone battery is low.
not made to work	Please charge the iPhone.
with iPhone” or	● iPhone is not properly
“This accessory is	docked.
not supported by
iPhone” appears on
iPhone screen.

■	USB
	Symptom	Possible cause
● Device cannot be		● Is there any MP3/WMA file
	detected.	available?
		● Is the device properly
		connected?
		● Is it an MTP device?
		● Does the device contain
		AAC file only?
● Playback does not		● Is it a copyright protected
	start.	WMA file?
		● Is it a false MP3 file?
● Wrong time display.		● Is Variable Bitrate file being
● Wrong file name		played back?
	display.	● Is the File Name written in
		Chinese or Japanese
		characters?
■	CD player
	Symptom	Possible cause
● Playback does not		● Is the disc loaded face
	start.	down?
● Playback stops in		● Does the disc satisfy the
	the middle or is not	standards?
	performed properly.	● Is the disc distorted or
		scratched?
● Playback sounds are		● Is the unit located near
	skipped, or stopped	excessive vibrations?
	in the middle of a	● Is the disc very dirty?
	track.	● Has condensation formed
		inside the unit?

■Tuner

Symptom Possible cause

●The radio makes ● Is the unit placed near the

unusual noises	TV or computer?
continuously.	● Is the FM/AM aerial placed
	properly? Move the aerial
	away from the AC power
	lead if it is located nearby.

E-20