23.Attach the Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and 1/4” Flat Washers (10).
24.Press a 1 1/2” Inner Cap (32) into the Seat Frame (36).
Insert a 1/4” x 2” Carriage Bolt (38) into the center of each Seat Plate (37). Attach the Seat Plates to
the Seat (13) with four 1/4” x 3/4” Screws (18).
Insert the two 1/4” x 2” Carriage Bolts (38) into the Seat Frame (36). Make sure that the Seat
(13)is turned so the wide end is towards the 1 1/2” Inner Cap (32). Tighten two 1/4” Nylon Lock Nuts (7) with 1/4” Flat Washers (10) onto the Carriage Bolts.
25.Press a 1 1/2” Inner Cap (32) into the Leg Lever
Lubricate a 5/16” x 2 1/4” Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the Bolt and a 5/16” Nylon Lock Nut (3). Do not
overtighten the Nylon Lock Nut; the Leg Lever must be able to pivot freely.
Insert the 5/16” x 2” Eyebolt (35) through the Leg Lever (29) from the indicated side. Slide a 5/16”
Flat Washer (8) onto the Eyebolt and tighten a 5/16” Nylon Lock Nut (3) onto the Eyebolt.
26.Set the bracket on the Seat Frame (36) on the indicated pins on the Front Upright (42). Attach the Seat Frame with a 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).
Press 3/4” Round Inner Caps (34) into the ends of the 13 1/2” Pad Tube (28) and the 13” Pad
Tube (31).
Insert the 13 1/2” Pad Tube (28) into the Seat Frame (36). Slide a 6” Pad (30) onto each end of the Pad Tube.
Insert the 13” Pad Tube (31) into the Leg Lever (29). Slide a 5 3/4” Pad (50) onto each end of the Pad Tube.
11
23 |
|
|
|
|
43 | 10 |
|
| 41 |
|
|
| 42 |
|
24 |
|
| 13 |
|
|
|
|
| |
|
|
|
| Wide |
|
|
|
| End |
37 |
| 38 |
|
|
|
|
|
| |
|
| 18 | 37 | 32 |
|
|
| ||
|
| 10 |
| 36 |
|
| 7 |
|
|
25 |
|
|
|
|
|
|
|
| 3 |
|
| 36 |
|
|
| 29 | |||
|
|
|
| |
|
| 35 |
| 8 |
|
|
|
| |
|
|
| 32 | 3 |
|
|
|
| |
26 | 40 | 36 |
|
|
|
|
| ||
|
|
|
| 34 |
|
|
|
| 30 |
14 |
|
|
| 28 |
42 |
|
|
|
|
Pin |
| 30 |
|
|
| 34 |
| 50 | |
|
|
| ||
|
|
| 29 | 31 |
|
|
| 50 |
|