Weslo WLSY71500 Nuts 3.Do not tighten the Nylon Lock Nuts yet, Do not tighten Nylon Lock Nuts yet

Page 5

3. Press the 1 1/4” Inner Cap (57) into the Front Upright

3

 

 

 

Single Hole

 

(42).

 

 

 

 

 

63

 

 

 

 

 

 

 

 

Attach the 1” Plastic Stop (64) to the center hole in

 

 

 

61

24

 

 

 

 

 

64

 

the Stop Bracket (63) with a 5/16” x 1 1/2” Bolt (24)

 

 

 

 

 

 

 

 

 

 

 

and 5/16” Jam Nut (2).

 

 

 

 

 

8

2

 

 

 

 

 

 

 

 

57

 

Attach the Stop Bracket (63) to the Front Upright (42)

 

 

 

 

 

 

 

 

 

 

 

with the 5/16” x 2” Bolt (61), a 5/16” Flat Washer (8)

 

 

 

3

 

 

and a 5/16” Nylon Lock Nut (3).

 

 

 

 

 

 

 

 

Slide the Front Upright (42) onto the two 5/16” x

 

 

 

 

 

 

2 1/2” Carriage Bolts (1) in the Base (4). Attach the

 

 

 

42

 

 

Front Upright to the Base with two 5/16” Nylon Lock

 

 

 

 

 

 

 

 

 

 

 

Nuts (3).Do not tighten the Nylon Lock Nuts yet.

 

 

 

 

 

 

 

 

 

 

 

 

4

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

4. Press two 2” Inner Caps (27) into the Top Frame (67).

4

 

11

 

 

 

 

 

 

 

 

11

11

 

Attach the Top Frame (67) to the Front Upright (42)

 

 

 

 

 

 

8

 

 

 

with two 5/16” x 2 3/4” Bolts (11), 5/16” Flat Washers

 

 

8

8

 

 

 

 

 

(8) and 5/16” Nylon Lock Nuts (3).

Do not tighten

 

 

 

 

67

 

the Nylon Lock Nuts yet.

 

 

 

 

 

 

 

 

Attach the Top Frame (67) to the Stop Bracket (63)

27

 

 

 

 

 

 

 

 

 

 

 

with a 5/16” x 2 3/4” Bolt (11), 5/16” Flat Washer (8)

 

 

 

 

3

27

and 5/16” Nylon Lock Nut (3).

Do not tighten the

 

 

3

 

 

 

 

 

 

 

3

 

 

Nylon Lock Nut yet.

 

 

 

 

 

63

 

Attach the Top Frame (67) to the Rear Upright (82)

 

82

 

42

 

 

with two 5/16” x 2 3/4” Bolts (11), 5/16” Flat Washers

 

 

 

 

 

 

 

 

 

 

 

(8) and 5/16” Nylon Lock Nuts (3).

 

 

 

 

 

 

 

Tighten all Nuts used in steps 2 through 4.

 

 

 

 

 

 

 

 

5. Set the two Weight Bumpers (19) on the indicated

5

 

 

 

 

 

plate on the Base (4). Align the holes in the Weight

 

 

 

 

 

 

 

 

 

 

 

Bumpers with the holes in the plate.

 

 

 

 

 

 

 

Stack seven Weights (25) on the Weight Bumpers

 

 

25

 

 

 

 

 

 

 

Pin Groove

 

(19). Each Weight must be turned so the pin groove

 

 

 

 

 

 

 

 

 

 

 

is facing the Front Upright (42). The holes in the

 

 

 

 

 

 

Weights must be aligned with the holes in the Weight

 

 

 

 

 

 

Bumpers.

CAUTION: Be careful to avoid tipping

 

 

 

 

19

 

 

the stack of Weights until step 6 is completed.

 

 

 

 

42

 

 

 

 

 

 

 

 

 

 

 

 

 

19

4

 

 

 

 

 

 

 

 

 

 

 

5

Image 5
Contents Customer HOT Line Patent Pending QUESTIONS?Model No. WLSY71500 Serial No Important Precautions Table of ContentsBody Before YOU BeginAssembly requires two people.Due to the size AssemblyFollowing Tools not Included are Required for Assembly Nuts yetDo not tighten Nylon Lock Nut yet Nuts 3.Do not tighten the Nylon Lock Nuts yetDo not tighten Nylon Lock Nuts yet Lubricate One of the Arms 46. Attach the Handle with a 5/16 Important As you assemble the Long Cable Bracket must be able to swivel freelySwivel Bracket must be able to swivel freely Page Manual Important The Short and Long CablesPage Important If the cables are Changing the Weight Setting AdjustmentTion will vary from the weight setting Switching the Arms to the Press Mode or Butterfly ModeAttaching the LAT BAR or Nylon Strap to LOW Pulley Station Attaching the LEG Lever to the LOW Pulley StationAttaching the LAT BAR or Nylon Strap to High Pulley Station Tightening the Cables TROUBLE-SHOOTING and MaintenancePart LIST-Model No. WLSY71500 Exploded DRAWING-Model No. WLSY71500 Cable Diagram Page Weslo INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty Remove this Part Identification Sheet from the Manual Inner Cap Round Cap 4 Inner Cap Cover Cap 2 Inner Cap