Weslo WLTL49806.0 user manual Troubleshooting, Problem The power turns off during use, Top

Page 21

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 12. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the two Foot Rail Screws

(4)and the two Hood Screws (96) and carefully re- move the Hood (1).

a

96

4

 

1

4

Locate the Reed Switch (63) and the Magnet (67) on the left side of the Pulley (64). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8". If necessary, loosen the 3/4” Tek Screw (38), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading.

1/8"

64

38

 

63

67

Top

 

View

 

21

Image 21
Contents Model No. WLTL49806.0 Serial No QUESTIONS?Call TOLL-FREE Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Page Back Right Side Before YOU BeginAssembly Tighten the Wheel Nut the Wheel should turn FreelyScrews are in the indicated holes Base Tighten the Upright Bolts yet Upright Bolts yetOuter side of the Frame Spacer facing Frame Bolt yet33, and a Nut 47 do not tighten the Frame Bolt yet Start all four Handrail Bolts before tightening Any of them Sembly. Make sure that no wires are pinchedSide View View from Above BoltsBase Cover not shown in the same way Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual Mode Measure your heart rate if desired Always exercise at a pace that is comfortable for youTurn on the fan if desired Whenkey. you are finished exercising, removeHOW to USE a Distance Program Select a distance programPress the Start button to start the program HOW to USE a Step Program When the program is completed, remove Key from the consoleSelect a step program HOW to USE a Calorie Goal Program Information Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useTop Problem The walking belt slows when walked on Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part LIST-Model No. WLTL49806.0Remove this Exploded Drawing and Part List from the Manual R1006A HOW to Order Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT