Keys Fitness T260, T240 owner manual Beeper test, Heart Rate System Test, Belt Alignment

Page 24

Beeper test

The beeper test will cause the beeper to sound.

1.Enter into Diagnostics menu, see Section 5.1.

2.Select the “BEEPER TEST” and accept it by pressing the JustGo®/ENTER key.

Listen for a series of “beeps”. The beeper test will stop automatically when you press the CLEAR/STOP key.

Heart Rate System Test

The heart rate system test allows you to determine if the optional heart rate system is working properly and that the computer is displaying your heart rate signal during a program.

1.In the Diagnostics menu, select the “HEART RATE TEST” and accept it by pressing the JustGo®/ ENTER key.

2.The top left display will show the signal received from the chest strap and the bottom window will show the hand grip signal (option). Attach your heart rate chest strap. You do not need to step on the treadmill for this test, but simply stand near the computer. Within a few seconds, your actual heart rate signal will be displayed on the screen. Do the same for the hand grip system ; put your hands on the two metal plates and wait for 5 to 8 seconds (T260).

3.Press the CLEAR/STOP key to terminate the test.

Belt Alignment

Should you need to adjust the tracking of the running belt, you must make all adjustments during the BELT ALIGNMENT procedure. To determine if the belt is not aligned along the center of the deck, measure the visible deck surface on both left and right sides of the belt. If these values are nearly equal, do not adjust the belt. If one side of the belt is closer to the foot rests than the other side, then you will need to adjust the belt to track to the opposite side.

To adjust running belt alignment.

1. You will need the 5/32” hex key to turn the bolts located inside the rear roller end caps.

WARNING – Do not stand on the belt during this procedure. Keep loose clothing and long hair away from the belt and rollers when performing belt alignment.

2.Allow the belt to reach 2.0 mph or 3.2 km/h (speed will be displayed on the computer screen). Looking from the rear of the treadmill, notice the gap between left and right sides of the belt and the foot rests.

If the running belt is tracking to the left of the deck surface:

turn the left bolt in a clockwise direction to allow the belt to track to the right and ultimately in the center, or;

turn the right bolt in a counter-clockwise direction to allow the belt to track to the right and ultimately in the center.

If the running belt is tracking to the right of the deck surface:

turn the left bolt in a counter-clockwise direction to allow the belt to track to the left and ultimately in the center, or;

turn the right bolt in a clockwise direction to allow the belt to track to the left and ultimately in the center.

NOTE – During any belt alignment procedure, do not turn each bolt by more than 1 to 1-1/2 revolutions. Exceeding this may

cause a high amount of tension on the running belt and result in premature wear of the belt and rollers. It is best to

adjust only one alignment bolt, since this will prevent the belt from excessive stretching resulting from adjustment of

both alignment bolts.

24

Image 24
Contents T240 T260 Contents IMPORTANTImportant SafetySAFETYNoticeNOTICE For Your Personal SafetyElectrical Information Know Your Heart RateT240 T260 Limited Warranty Responsibility of the UserOperatiOperating your Getting to know the T240 T260 Computer display MonitorScanning Feature KeysPausing During an Exercise Saving an Exercise custom programsSettingtti Up the Computer tto Your Environment Access to Settings MenuLanguage Feature Viewing Exercise ParametersWeight Unit Feature User Identification FeatureActivate User Create UserReset Statistics Edit UserView Statistics Delete UserDistance Unit Feature Time, Distance or Calories FeatureWarm Up and Cool Down Feature Table of minimum and maximum valuesHeart Rate Control Options Feature Heart Rate Access Options FeatureBeeper Feature Speed LimitsBig Number Option Learn Program T260Heart Rate Recovery T260 only ExercisExercise ProgramsProgram Levels JustGo Program Manual ProgramHill Climb Program T260 only Speed Run Program T260 only Track Program T260 onlyHeart Rate Control Program HRC and Weight Loss Program Cardiovascular Program Memory & Learn ProgramsWalk Program Heart Rate Access Feature How to Use Heart Rate AccessChanging Your Target Heart Rate in a Program Usingsi a Heart Rate Receiveri r Access to Diagnostics menu Problem Possible Cause SolutionNvram Test Eprom testKeypad Test Display TestBeeper test Heart Rate System TestBelt Alignment Motor Check Elevation CalibrationSafety Key test Error logStatistics Speed sensor testMaintenance InformationInfor ation MaintenanceGeneral Care Belt and Running Deck Running Belt Deck SurfaceQuick Troubleshooting Check List Problem Possible CAUSE/SOLUTIONError Codes Thank You for Purchasing a Bodyguard T240 T260Safety requirements North America InternationalInterference limits requirements North America Designed and Engineered in Canada