NordicTrack NTL77806.1 manual Top View Problem The walking belt slows when walked on

Page 23

Locate the Reed Switch (22) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, move the Reed Switch slightly using a slotted screwdriver. Reattach the Motor Hood (not shown), making sure that the 3/4” Screws (not shown) are inserted into the same holes from which they were removed. Run the treadmill for a few minutes to check for a correct speed reading.

Top

View

22

1/8”

17

18

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walk- ing belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

3”–4”

 

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, please see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the allen wrench to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tight- ened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

a

b

23

Image 23
Contents Call TOLL-FREE QUESTIONS?Model No. NTL77806.1 Serial No Table of Contents Important Precautions Page Before YOU Begin Treadmill is completely assembled AssemblyMake sure that the power cord is unplugged Ble. Do not fully fold the Frame untilAgain. if the Connectors are not CON Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the Power18. Note For simplicity, all instructions Your heart rate accurately. Before usingMake sure that your hands are clean Training ZonesWhenkey. you are finished exercising, remove Turn on the fan if desiredSelect one of the preset programs HOW to USE a Preset ProgramSelect one of the custom programs HOW to Create a Custom ProgramFollow your progress with the displays HOW to USE a Custom Program Insert an iFIT Card and select a program HOW to USE AN Ifit CardUSER’S Mode Optional Chest Pulse Sensor HOW to Adjust the Cushioning SystemHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop View Problem The walking belt slows when walked on Page Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description R0806AOrdering Replacement Parts Exploded Drawing a Exploded Drawing B-Model No. NTL77806.1 Exploded Drawing C-Model No. NTL77806.1 Exploded Drawing D-Model No. NTL77806.1 Limited Warranty