NordicTrack NTL07007.1 HOW to Fold and Move the Treadmill, HOW to Fold the Treadmill for Storage

Page 23

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE

Before folding the treadmill, adjust the incline to the lowest position. If you do not do this, you may damage the treadmill when you fold it. Remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.

1.Hold the metal frame firmly in the location shown by the arrow at the right. CAUTION: To decrease the pos- sibility of injury, do not lift the frame by the plastic foot rails. Make sure to bend your legs and keep your back straight as you raise the frame. Raise the frame about halfway to the vertical position.

2.Raise the frame until the latch knob locks into the storage position. Make sure that the latch knob is locked in the storage position.

To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of di- rect sunlight. Do not leave the treadmill in the stor- age position in temperatures above 85° F (30° C).

HOW TO MOVE THE TREADMILL

Before moving the treadmill, convert the treadmill to the stor- age position as described above. Make sure that the latch knob is locked in the storage position.

1.Hold a handrail and the frame and place one foot against one of the wheels.

2.Tilt the treadmill back until it rolls freely on the wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not attempt to move the treadmill over an uneven surface.

3.Place one foot against a wheel, and carefully lower the treadmill until it is resting in the storage position.

Frame

Latch Knob

Frame

Handrail

Wheels Base

23

Image 23
Contents Call TOLL-FREE QUESTIONS?Model No. NTL07007.1 Serial No Table of Contents Important Precautions Page Before YOU Begin Hardware may be included AssemblyNut the Wheel must turn freely. Discard Make sure that the power cord is unpluggedSee the inset drawing. Tie the wire tie Do not fully fold the Frame yetFully tighten the Bolts yet Be careful not to pinch the Upright WireSee assembly steps 4 and 6. Firmly tighten the 3/8 x 4 Bolts Pull on the sleeve to make sure that it is locked into place Make sure that no wires are pinched PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the Console Start the walking belt and adjust the speed HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeTime/Incline dis Monitor your progress with the displays Matrix-When youChange the incline of the treadmill as desired Measure your heart rate if desired Press the Start button to start the workout HOW to USE a Preset WorkoutSelect a preset workout Press the Start Workout button to start the workout HOW to USE the Custom Workout CenterSelect the Custom Workout Center Press the Start Fitness Test button to start the workout HOW to USE the Fitness Test WorkoutPut on the chest pulse sensor Select the fitness test workoutHOW to USE the Sound System Monitor your progress with the displays HOW to USE AN Ifit CardInsert an iFIT card and select a workout Optional Chest Pulse Sensor Information ModeHOW to Adjust the Cushioning System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingView Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description R0108AQty Exploded Drawing A-Model No. NTL07007.1 Exploded Drawing B-Model No. NTL07007.1 Exploded Drawing C-Model No. NTL07007.1 Exploded Drawing D-Model No. NTL07007.1 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty