NordicTrack NTL07007.1 user manual View

Page 26

Remove the three #8 x 3/4" Screws (12) and care- fully pivot the Hood (61) off.

Locate the Reed Switch (71) and the Magnet (50) on the left side of the Pulley (51). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If neces- sary, loosen the 3/4" Reed Switch Screw (15), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a cor- rect speed reading.

PROBLEM: The walking belt slows when walked on

12

61

1/8 in.

15

50

71

51

Top

View

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

b	2–3 in.

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the front cover of this manual.

26

Image 26

Contents Call TOLL-FREE QUESTIONS?Model No. NTL07007.1 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Hardware may be includedDo not fully fold the Frame yet Make sure that the power cord is unpluggedSee the inset drawing. Tie the wire tie Nut the Wheel must turn freely. DiscardBe careful not to pinch the Upright Wire Fully tighten the Bolts yetSee assembly steps 4 and 6. Firmly tighten the 3/8 x 4 Bolts Pull on the sleeve to make sure that it is locked into place Make sure that no wires are pinched PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the Console Select the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Start the walking belt and adjust the speedTime/Incline dis Monitor your progress with the displays Matrix-When youChange the incline of the treadmill as desired Measure your heart rate if desired Press the Start button to start the workout HOW to USE a Preset WorkoutSelect a preset workout Press the Start Workout button to start the workout HOW to USE the Custom Workout CenterSelect the Custom Workout Center Select the fitness test workout HOW to USE the Fitness Test WorkoutPut on the chest pulse sensor Press the Start Fitness Test button to start the workoutHOW to USE the Sound System Monitor your progress with the displays HOW to USE AN Ifit CardInsert an iFIT card and select a workout Optional Chest Pulse Sensor Information ModeHOW to Adjust the Cushioning System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useView Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0108A Key No. Qty DescriptionQty Exploded Drawing A-Model No. NTL07007.1 Exploded Drawing B-Model No. NTL07007.1 Exploded Drawing C-Model No. NTL07007.1 Exploded Drawing D-Model No. NTL07007.1 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty