Woodstock M1036 owner manual Collets, To install the collet chuck, do these steps

Page 22
Note: This lip and groove pulls the collet from the spindle when the collet nut is removed.
2. Place the collet nut and collet into the collet chuck and finger tighten the collet nut onto the collet chuck.
3. Insert the bit into the collet, place a hex wrench through the hole in the spindle, and tighten the collet with a 22mm wrench (see Figure 25).
To remove a bit from the collet chuck, do these steps:
1. Protect the table surface with a piece of cardboard or hold the cutter or tool with a shop towel to pre- vent it from falling out of the collet.
2. Place a hex wrench through the hole in the spindle and loosen the collet nut with a 22mm wrench until the bit is free.
Note: Remove the collet chuck in the same manner as removing the drill chuck.
-20-

M1036 Micro Mill

Collets

OPERATIONS

The collet chuck (an optional accessory) for the micro mill offers increased precision and rigidity compared to the drill chuck. Each collet will only fit tooling with a specific shaft diameter. This collet set includes 1⁄4", 3⁄16", 5⁄32", 5⁄64", 3⁄64" collets.

To install the collet chuck, do these steps:

1.UNPLUG THE MICRO MILL!

2.Remove the drill chuck and clean the arbor and collet chuck tapers with denatured alcohol.

3.Push the collet chuck onto the arbor.

4.Place a piece of wood on the compound slide table and use the downfeed lever to firmly press the collet chuck against the piece of wood (see Figure 23) to seat the collet chuck on the arbor.

To install the collet in the collet chuck, do these steps:

1.Place the grooved end of the collet into the collet nut until the off-center lip of the collet nut snaps into the collet groove. See Figure 24.

Figure 23. Installing the collet chuck.

Off-Center Collet Lip

and Collet Groove

Figure 24. Collet and collet nut lip.

Figure 25. Installing a collet.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Micro Mill Page Contents Maintenance Woodstock Technical Support SpecificationsIntroduction About Your New Micro MillControls and Features M1036 Controls and featuresSafety Standard Safety InstructionsSafety Additional Safety Instructions for Micro Mills Extension Cords Electrical110V Operation GroundingUnpacking SET UPItems Needed for Set Up Bench Mounting Hardware OptionalInventory Box 1 Contents Figure QtyBox 2 Contents Figure Qty Box 1 Tools and Hardware Not Shown QtyMachine Placement Cleaning MachineMounting Headstock to Column To install the headstock on the column, do these stepsMounting to Workbench To mount the mill to the workbench, do these stepsCompound Slide Table To install the compound slide table, do these stepsTo install the vise, do these steps ViseTest Run and Spindle Break-in General OperationsTable Travel Backlash Graduated DialsHeadstock Height To use the downfeed lever, do this step Downfeed ControlsDigital Height Gauge To use the micro downfeed handwheel, do these stepsTo set the depth stop, do these steps Depth StopChanging RPM To change the RPM, do these stepsDrill Chuck Removal To install a drill bit, do these stepsDrill Chuck To remove a drill bit, do these stepsTo install the collet in the collet chuck, do these steps To install the collet chuck, do these stepsCollets Cleaning MaintenanceTable & Base Lubrication Cross slide and saddle ways Quill shaftTo adjust the gibs, do these steps ServiceGibs Replacing Motor Brushes Fuse ReplacementUnscrew the cap from the motor housing see Figure To replace the motor brushes, do these stepsElectrical Components Troubleshooting Symptom Possible Cause Corrective ActionParts Parts List PART# DescriptionFLATWASHER24MM Warranty Warranty Registration CommentsBOX BELLINGHAM, WA
Top Page Image Contents