Gold's Gym GGTL39608.0 manual Ful not to pinch any wires

Page 10

8. Insert the wires into the Right Upright (78). Set

8

 

 

 

 

 

Console

the brackets on the console assembly into the

 

 

 

 

 

Right Upright and the Left Upright (77). Be care-

 

 

 

 

 

 

Assembly

ful not to pinch any wires.

 

 

 

 

 

 

 

Attach the console assembly with four 5/16" x

 

 

 

 

 

 

 

3/4" Bolts (2) and four 5/16" Star Washers (5).

 

 

 

 

 

 

 

Start all four Bolts before firmly tightening

 

2

 

 

 

2

 

them.

 

 

 

 

 

 

 

5

 

 

2

5

 

 

 

 

5

2

77

 

 

78

 

 

 

 

 

9. Set the Left Handrail (69) and the Right Handrail

9

 

 

3

3

 

 

(71) on a level surface.

71

 

69

 

Attach the Handrails (69, 71) to the Handrail

 

 

 

 

 

Bracket (70) with four 1/4" x 1 1/2" Bolts (3) and

 

 

 

 

 

 

 

four 1/4" Nuts (4). See the lower drawing.

 

 

 

 

 

 

 

Make sure that the Nuts sit inside the indi-

 

 

4

 

4

 

 

cated square holes in the Handrails. Start all

 

 

70

 

 

four Bolts before firmly tightening them.

 

 

 

 

 

 

 

71

 

Square Holes

69

 

 

4

 

 

4

10. Hold the Pulse Assembly (72) near the Handrail

10

 

 

 

 

Bracket (70). Orient the Pulse Assembly so

 

 

 

 

that the indicated plastic boss will fit into the

 

 

 

 

 

hole in the Right Handrail (71). Make sure that

 

Boss

Pulse Wires

 

72

the two Pulse Ground Wires (86) are extending

 

 

from the top of the Handrail Bracket. Connect

71

 

86

 

 

the two Pulse Ground Wires to the ground wires

 

 

 

 

on the Pulse Assembly.

 

 

 

 

 

Next, insert the wire harness on the Pulse

 

 

 

 

69

Assembly (72) into the top of the Handrail

 

 

70

7

Bracket (70) and out of the side as shown.

7

 

 

Set the Pulse Assembly (72) on the Handrails

Wire Harness

 

 

(69, 71). Insert the excess ground wire into the

 

 

 

Handrails. Attach the Pulse Assembly with four

 

 

 

 

 

#8 x 3/4" Screws (7). Be careful not to over-

 

 

 

 

 

tighten the Screws. Be careful not to pinch

 

 

 

 

 

any wires.

10

 

 

 

 

 

 

 

 

 

Image 10
Contents QUESTIONS? Model No. GGTL39608.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Tighten the Bolts yet Not overtighten the Bolts the Wheels should Turn freelyDoes not fall into the Right Upright See the far right drawing. Wrap the wire tieMake sure that the end of the Upright Wire See the left inset drawing. Identify the twoAged When the Power is Turned on Connectors are not ConnectedPROPERLY, the Console MAY be DAM Ful not to pinch any wires Start all four Bolts before firmly tightening ThemBe Damaged When the Power is Turned on If the Connectors are not CONNected PROPERLY, the Console MAY Side View View from Above HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Start the walking beltMeasure your heart rate if desired. Before using HOW to USE a Preset Workout Information Mode HOW to USE the DumbbellsHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Top View Problem The walking belt slows when walked onKey and Unplug the Power CORD. Using Walking belt has shifted to the right, turn the leftWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. GGTL39608.0 Key No. Qty DescriptionExploded Drawing Exploded Drawing B-Model No. GGTL39608.0 R0310A Exploded Drawing C-Model No. GGTL39608.0 R0310A Exploded Drawing D-Model No. GGTL39608.0 R0310A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT