Gold's Gym GGTL39608.0 manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 20

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 13). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 13. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

 

 

To reset the circuit breaker, wait for five minutes

Tripped

Reset

and then press the switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 18 to turn off the demo mode.

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

24

POWER CORD. Remove the two #12 x 1 1/4"

27

Screws (27) and the two #8 x 3/4" Hood Screws (24)

 

27

and carefully remove the Motor Hood (62).

 

 

 

 

 

62

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents QUESTIONS? Model No. GGTL39608.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Tighten the Bolts yet Not overtighten the Bolts the Wheels should Turn freelySee the far right drawing. Wrap the wire tie Make sure that the end of the Upright WireDoes not fall into the Right Upright See the left inset drawing. Identify the twoPROPERLY, the Console MAY be DAM Connectors are not ConnectedAged When the Power is Turned on Ful not to pinch any wires Start all four Bolts before firmly tightening ThemNected PROPERLY, the Console MAY If the Connectors are not CONBe Damaged When the Power is Turned on Side View View from Above PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Start the walking beltMeasure your heart rate if desired. Before using HOW to USE a Preset Workout Information Mode HOW to USE the DumbbellsHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USECompatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use View Problem The walking belt slows when walked on Key and Unplug the Power CORD. UsingTop Walking belt has shifted to the right, turn the leftExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. GGTL39608.0 Key No. Qty DescriptionExploded Drawing Exploded Drawing B-Model No. GGTL39608.0 R0310A Exploded Drawing C-Model No. GGTL39608.0 R0310A Exploded Drawing D-Model No. GGTL39608.0 R0310A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents