Gold's Gym GGBE8057.0 manual Screws yet

Page 13

16.Orient the Center Upright (13) as shown and insert it into the Base (14). Hold the Foot Plate (15) and the Weight Carriage Base (20) against the Base. Attach the Foot Plate, Center Upright, and Weight Carriage Base to the Base with two M10 x 110mm Screws (130). Do not tighten the

Screws yet.

Attach the Foot Plate (15) to the Center Upright

(13)with an M10 x 93mm Bolt (129), an M10 Washer (148), and an M10 Nylon Locknut (153).

17.Attach the Top Frame (17) to the Rear Uprights (12) with four M10 x 110mm Screws (130) and four M10 Washers (148). Do not tighten the

Screws yet.

Attach the Top Frame (17) to the Front Uprights (11) in the same way.

Press four 75mm Square Inner Caps (95) into the corners of the Top Frame (17).

16
		Bracket
	13	153
		148
129		20
129
130		14
130
	15
17	95
	130
	148
		17
		95
		130
	12	148
	95	148
		12
		148
	11	130

13

Image 13

Contents Model No. GGBE8057.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Right Side Before YOU BeginLeft Side Part Identification Chart Page Make Assembly Easier AssemblyDo not tighten the Screws yet Nylon Locknut yet M10 Washers 148. Tighten the Screws used in steps 1153 148 155 Grease 123 Opening 124 122 170 172 154 Page 122 Large Hole Holes 180 Thick 131 End Posts Screws yet 115 109 112 153 Hole 148 151 127 Page Not tighten the Nylon Locknuts yet Overtighten the Screw the Right AdjustmentPage Attach the other Swivel Bracket not shown in the same way Attach the other Barbell Adapter not shown in the same wayScrew the Tether must rotate easily Cable in the groove of the V-pulley Sure that the Cable Trap is oriented to holdOriented to hold the Cable in the groove Pulley Locknut 153. Make sure that the Cable Trap isIdentify the High Cable 81. Feed the Cable 153 153 See the inset drawing. Insert the Cabling Rod Page Trap and the Half Pulley Guards are oriented as shown 153 140 148 151 127 125 Pulley Guards are oriented as shown Adjusting the Seat and Backrest AdjustmentAttaching the Curl PAD Attaching the Curl BARUsing the Weight Rests and the Weight Spotters Using the LEG LeverAdjust the right Barbell Spotter not shown in the same way Moving the Barbell SpottersAdjusting the Arms Using the Locking BARAdding Weights to the Barbell or the Weight Carriage Arm 22 in the same wayAttaching the Accessories to the LOW Pulley Station Attaching the Accessories to the High Pulley StationTightening the Cables MaintenanceHigh Cable Cable DiagramRear Cable Low CableExercise Guidelines Cooling Down Muscle ChartStaying Motivated Aerobic Exercise Weight Sets Reps Thursday Exercise Weight Sets RepsFriday Qty Description Part LIST-Model No. GGBE8057.0111 Exploded Drawing A-Model No. GGBE8057.0 R0607A Exploded Drawing B-Model No. GGBE8057.0 Exploded Drawing C-Model No. GGBE8057.0 Exploded Drawing D-Model No. GGBE8057.0 R0607A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT