Gold's Gym GGBE8057.0 manual Trap and the Half Pulley Guards are oriented as shown

Page 26

50.Wrap the Rear Cable (94) under a Small Pulley

(74).Attach the Small Pulley, a Small Cable Trap (93), and two Half Pulley Guards (91) at the sec- ond hole from either end of the two Pulley Plates

(92)with an M10 x 48mm Bolt (125) and an M10 Nylon Locknut (153). Make sure that the Cable

Trap and the Half Pulley Guards are oriented as shown.

51.Attach the Rear Cable (94) inside the Weight Carriage Frame (18) with an M10 x 55mm Bolt (127), two M10 Washers (148), and an M10 Nylon Locknut (153).

52.Identify the Low Cable (80). Route the threaded end of the Cable through the Foot Plate (15) and the Center Upright (13).

Wrap the Low Cable (80) under a Large Pulley (165). Attach the Large Pulley inside the Center Upright (13) with an M10 x 93mm Bolt (129), two M10 Washers (148), two M10 x 25mm Spacers (169), and an M10 Nylon Locknut (153).

50
91
	94
153	74	93
		93
		91
	92	125
51
153	148	18
		148
		127
		94

52
153	165
148	13
169
	169
15	148
	129
80

26

Image 26

Contents Call TOLL-FREE QUESTIONS?Model No. GGBE8057.0 Serial No Table of Contents Important Precautions Left Side Before YOU BeginRight Side Part Identification Chart Page Do not tighten the Screws yet AssemblyMake Assembly Easier M10 Washers 148. Tighten the Screws used in steps 1 Nylon Locknut yet153 148 155 Grease 123 Opening 124 122 170 172 154 Page 122 Large Hole Holes 180 Thick 131 End Posts Screws yet 115 109 112 153 Hole 148 151 127 Page Overtighten the Screw the Right Adjustment Not tighten the Nylon Locknuts yetPage Attach the other Barbell Adapter not shown in the same way Attach the other Swivel Bracket not shown in the same wayScrew the Tether must rotate easily Sure that the Cable Trap is oriented to hold Cable in the groove of the V-pulleyIdentify the High Cable 81. Feed the Cable Locknut 153. Make sure that the Cable Trap isOriented to hold the Cable in the groove Pulley 153 153 See the inset drawing. Insert the Cabling Rod Page Trap and the Half Pulley Guards are oriented as shown 153 140 148 151 127 125 Pulley Guards are oriented as shown Attaching the Curl PAD AdjustmentAdjusting the Seat and Backrest Attaching the Curl BARAdjust the right Barbell Spotter not shown in the same way Using the LEG LeverUsing the Weight Rests and the Weight Spotters Moving the Barbell SpottersAdding Weights to the Barbell or the Weight Carriage Using the Locking BARAdjusting the Arms Arm 22 in the same wayAttaching the Accessories to the High Pulley Station Attaching the Accessories to the LOW Pulley StationMaintenance Tightening the CablesRear Cable Cable DiagramHigh Cable Low CableExercise Guidelines Staying Motivated Muscle ChartCooling Down Friday Exercise Weight Sets RepsAerobic Exercise Weight Sets Reps Thursday Part LIST-Model No. GGBE8057.0 Qty Description111 Exploded Drawing A-Model No. GGBE8057.0 R0607A Exploded Drawing B-Model No. GGBE8057.0 Exploded Drawing C-Model No. GGBE8057.0 Exploded Drawing D-Model No. GGBE8057.0 R0607A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty