Gold's Gym GGBE8057.0 manual Attach the other Barbell Adapter not shown in the same way

Page 18

29.Orient the Locking Bar (114) as shown. Hold the Locking Bar between the left Barbell Carriage (104) and the right Barbell Carriage (not shown). Insert the Barbell (113) into the left Barbell Carriage, the Locking Bar, and the right Barbell Carriage. Center the Barbell in the Barbell Carriages. Then, engage the Locking Bar into slots in the Front Uprights (11).

30.Attach a Barbell Adapter (102) to the Barbell

(113) with an M10 x 25mm Screw (128) and a Large Washer (135). Then, press a 48mm x 3mm Round Inner Cap (103) into the Barbell Adapter.

Attach the other Barbell Adapter (not shown) in the same way.

31.Insert a Phillips screwdriver into the indicated hole in a Swivel Bracket (31). Use the Phillips screwdriver to tighten the Trunnion (70) and the Swivel Bracket into the Top Frame (17).

Attach the other Swivel Bracket (not shown) in the same way.

29
		104
114			113
		11
30
			135
		113	128
		113
			103
			102
31
		17
		70
	31	Hole
	31

18

Image 18

Contents QUESTIONS? Model No. GGBE8057.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Before YOU Begin Right SideLeft Side Part Identification Chart Page Assembly Make Assembly EasierDo not tighten the Screws yet M10 Washers 148. Tighten the Screws used in steps 1 Nylon Locknut yet153 148 155 Grease 123 Opening 124 122 170 172 154 Page 122 Large Hole Holes 180 Thick 131 End Posts Screws yet 115 109 112 153 Hole 148 151 127 Page Overtighten the Screw the Right Adjustment Not tighten the Nylon Locknuts yetPage Attach the other Barbell Adapter not shown in the same way Attach the other Swivel Bracket not shown in the same wayScrew the Tether must rotate easily Sure that the Cable Trap is oriented to hold Cable in the groove of the V-pulleyLocknut 153. Make sure that the Cable Trap is Oriented to hold the Cable in the groove PulleyIdentify the High Cable 81. Feed the Cable 153 153 See the inset drawing. Insert the Cabling Rod Page Trap and the Half Pulley Guards are oriented as shown 153 140 148 151 127 125 Pulley Guards are oriented as shown Attaching the Curl PAD AdjustmentAdjusting the Seat and Backrest Attaching the Curl BARAdjust the right Barbell Spotter not shown in the same way Using the LEG LeverUsing the Weight Rests and the Weight Spotters Moving the Barbell SpottersAdding Weights to the Barbell or the Weight Carriage Using the Locking BARAdjusting the Arms Arm 22 in the same wayAttaching the Accessories to the High Pulley Station Attaching the Accessories to the LOW Pulley StationMaintenance Tightening the CablesRear Cable Cable DiagramHigh Cable Low CableExercise Guidelines Muscle Chart Cooling DownStaying Motivated Exercise Weight Sets Reps Aerobic Exercise Weight Sets Reps ThursdayFriday Part LIST-Model No. GGBE8057.0 Qty Description111 Exploded Drawing A-Model No. GGBE8057.0 R0607A Exploded Drawing B-Model No. GGBE8057.0 Exploded Drawing C-Model No. GGBE8057.0 Exploded Drawing D-Model No. GGBE8057.0 R0607A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT