JVC LVT1040-003A manual Adjusting the Brightness Dimmer at Power On, Adjusting the Volume

Page 14

Basic Operations

Adjusting the Brightness (DIMMER - at Power On)

You can adjust the brightness of the display.

When the System is Turned On

At power on, each time you press the DIMMER button on the Remote Control, the brightness changes as follows: DIMMER OFF=DIMMER 1=DIMMER 2=(back to the beginning)

DIMMER OFF : Bright

DIMMER 1 : Dark (CD lamp also becomes dark.)

DIMMER 2 : Darker (CD lamp goes out.)

Power Saving Mode (DIMMER - at Power Off)

In power saving mode, you can save the power while the System is turned off (Standby Mode).

Each time you press the DIMMER button on the Remote Control at power off, the display alternates as follows.

DISPLAY ONÔDISPLAY OFF

To enable Power Saving mode, set to “DISPLAY OFF”.

The display completely turns off to save the power.

To restore normal power mode, reset to “DISPLAY ON”. The Clock indicator () and the clock appear on the display.

Adjusting the Volume

Turn the VOLUME control on the Unit clockwise to in- crease the volume or turn it counterclockwise to decrease the volume.

Press the VOLUME + button on the Remote Control to in- crease the volume or press the VOLUME _ button on the Remote Control to decrease the volume.

You can adjust the volume level between 0 and 50.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers.

Be sure to turn down the volume before connecting or put- ting on headphones.

CAUTION:

DO NOT turn off the System with the volu- me set to an extremely high level; otherwi- se a sudden blast of sound could damage your hearing, speakers and/or headphones when you turn on the System or start play- ing any source next time.

REMEMBER you cannot adjust the volume level while the System is in standby mode.

Fade-out Muting (FADE MUTING)

You can mute the output with one touch operation.

To mute the output, press the FADE MUTING button on the Remote Control. Then, “FADE MUTING” blinks and the output will be faded out and becomes 0.

To release muting, press the FADE MUTING button once again. Then, the output will be faded in to the original level.

Adjusting the volume causes the muting process (fading out to 0) to release.

If you use the AHB PRO button or the BASS/TREBLE but- ton during muting, the FADE MUTING button does not

work to release muting. In this case, turn the VOLUME control on the Unit or the VOLUME+/ _ button on the Re- mote Control to newly set the volume.

Reinforcing the Bass Sound (Active Hyper Bass Pro.)

You can reinforce the bass sound to maintain rich, full bass at low volume. (This effect does not apply to the headphones.)

To get the effect, press the AHB PRO button on the Unit or the Remote Control.

“AHB PRO ON” appears and the “BASS” indicator lights up. To cancel the effect, press the AHB PRO button again. “AHB PRO OFF” appears and the “BASS” indicator goes out.

11

Image 14
Contents FS-X1/FS-X3 Important for Laser Products Above ALL How This Manual Is Organized FeaturesIntroduction Table of Contents Troubleshooting Care And Maintenance Specifications Using the Remote Control AccessoriesHow To Put Batteries In the Remote Control Getting StartedUsing the Coaxial Type Connector Not Supplied Connecting the FM AntennaUsing the Supplied Wire Antenna Connecting the AM MW Antenna Connecting the Speakers SP-FSX1/SP-FSX3 When removing Connecting a Powered SubwooferConnecting an External Equipment When attaching the speaker grillsConnecting an MD Recorder, etc Optical Digital Output Automatic Power OnChanging the Source Turning the Power On and OffBasic Operations Adjusting the Volume Adjusting the Brightness Dimmer at Power OnPower Saving Mode Dimmer at Power Off Fade-out Muting Fade MutingAuto Power Off A.P.off No signal conditionTo disable the A.P.off function Entering the Number with the Remote Control Numeric KeysSelect a station using one of the follow- ing methods Using the TunerTuning In a Station One Touch RadioTo change the preset stations, repeat the same Presetting StationsTo Change the FM Reception Mode Beat Cut AM MW ReceptionPress the PTY Search button within approx seconds again Receiving FM Stations with RDSTo search for a program by PTY codes Affairs AlarmNews InfoAlarm function Test functionTo Insert a CD Using the CD PlayerWhen playing a CD-R or CD-RW Quickest Way To Start a CD Is With the One Touch OperationProgramming the Playing Order of the Tracks Program Play Basics of Using the CD Player Normal PlayTo Unload a CD Random Play Press the CD 6button on the Remote ControlTo Modify the Program Repeat to program the other tracksUnlocking the CD door Repeating TracksLocking the CD door Turn off the systemChanging the Equipment’s Name Using External EquipmentsListening to External Equipment To exit the source LINE, select other source e.g. CDPress the SET button to finish the adjustment Adjusting the Input LevelWhen the source is LINE, press and hold the SET button Recording the System’s Source to External EquipmentPress the CLOCK/TIMER button Using the TimersSetting the Clock Press the 3 or 2 button to set the hourShowing the Clock Display Setting the Daily TimerPerform steps 2 to 5 in Setting the Clo- ck on Correcting the ClockSelecting the music source Setting the on time ExampleSetting the OFF time Example Press the Cancel button Turning the Daily Timer On and OffSetting the volume level Select the Fade functionDuring playback a source, press the Sleep button Setting the Sleep TimerTimer Priority Wait for a few secondsPossible Cause TroubleshootingSymptom ActionCare And Maintenance Specifications 0403MNMCREJEM