JVC LVT1040-003A Tone Control BASS/TREBLE, No signal condition, To disable the A.P.off function

Page 15

Basic Operations

Tone Control (BASS/TREBLE)

You can control the tone by changing the bass (low frequen- cy) and treble (high frequency).

On the Remote Control

1 Press the BASS/TREBLE button.

Each time you press the button, the Tone Control mode changes as follows.

BASS=TREBLE=Normal display=(back to the beginning)

2 While “BASS” or “TREBLE” appears on the display, press the VOLUME + or - button to adjust the bass or treble level.

You can change the level within the range of -5 to +5. (0: flat)

No signal condition:

Source CD: CD is stopped or no CD is inserted.

When no signal condition continues, “A.P.off 20 sec” (20 seconds left before elapsed time reaches three minutes) ap- pears on the display. The displayed time is counted down and, finally, the System is turned off (Standby mode).

•If a CD is played back, the “A.P.off” indicator stops blinking and stays lit again.

•If you press a button or turn the VOLUME control, three-minute counting down is reset and counting down newly restarts.

To disable the A.P.off function

When the source is “CD”, press the A.P.off button on the Remote Control until “A.P.off STOP” appears on the dis- play.

Then, the “A.P.off” indicator goes out.

3 Press the BASS/TREBLE button until normal display appears.

Waiting for five seconds will also return the System to the normal display.

Auto Power Off (A.P.off)

You can automatically turn off the System when no signal condition continues for three minutes. This function is ef- fective when the source is set to “CD”, but not to “FM”, “AM” or “ LINE”.

To Enable the A.P.off function (When the source is “CD”)

1 Press the A.P.off button on the Remote Control until “A.P.off SET” appears on the display.

Then, the “A.P.off” indicator lights up on the display.

•Each time you press the button, the display alternates as follows.

A.P.off SET Ô A.P.off STOP

When no signal condition is detected, the “A.P.off” indica- tor will start blinking soon.

Entering the Number with the Remote Control (Numeric Keys)

You will use the Numeric Keys on the Remote Control to enter numbers for presetting stations, recalling the preset stations, selecting track number, or programming the play- ing tracks on a CD.

How to enter the number with the Numeric Keys is ex- plained here.

Examples:

•To enter number 5, press 5.

•To enter number 10, press 10.

•To enter number 15, press +10 then 5.

•To enter number 20, press +10 then 10.

•To enter number 25, press +10, +10, then 5.

12

Page 14 Page 16
Image 15
Page 14 Page 16
Contents FS-X1/FS-X3 Important for Laser Products Above ALL Features IntroductionHow This Manual Is Organized Table of Contents Troubleshooting Care And Maintenance Specifications Getting Started AccessoriesHow To Put Batteries In the Remote Control Using the Remote ControlConnecting the FM Antenna Using the Supplied Wire AntennaUsing the Coaxial Type Connector Not Supplied Connecting the AM MW Antenna Connecting the Speakers SP-FSX1/SP-FSX3 When attaching the speaker grills Connecting a Powered SubwooferConnecting an External Equipment When removingAutomatic Power On Connecting an MD Recorder, etc Optical Digital OutputTurning the Power On and Off Basic OperationsChanging the Source Fade-out Muting Fade Muting Adjusting the Brightness Dimmer at Power OnPower Saving Mode Dimmer at Power Off Adjusting the VolumeEntering the Number with the Remote Control Numeric Keys No signal conditionTo disable the A.P.off function Auto Power Off A.P.offOne Touch Radio Using the TunerTuning In a Station Select a station using one of the follow- ing methodsBeat Cut AM MW Reception Presetting StationsTo Change the FM Reception Mode To change the preset stations, repeat the sameReceiving FM Stations with RDS To search for a program by PTY codesPress the PTY Search button within approx seconds again Info AlarmNews AffairsTest function Alarm functionQuickest Way To Start a CD Is With the One Touch Operation Using the CD PlayerWhen playing a CD-R or CD-RW To Insert a CDBasics of Using the CD Player Normal Play To Unload a CDProgramming the Playing Order of the Tracks Program Play Repeat to program the other tracks Press the CD 6button on the Remote ControlTo Modify the Program Random PlayTurn off the system Repeating TracksLocking the CD door Unlocking the CD doorTo exit the source LINE, select other source e.g. CD Using External EquipmentsListening to External Equipment Changing the Equipment’s NameRecording the System’s Source to External Equipment Adjusting the Input LevelWhen the source is LINE, press and hold the SET button Press the SET button to finish the adjustmentPress the 3 or 2 button to set the hour Using the TimersSetting the Clock Press the CLOCK/TIMER buttonCorrecting the Clock Setting the Daily TimerPerform steps 2 to 5 in Setting the Clo- ck on Showing the Clock DisplaySetting the on time Example Setting the OFF time ExampleSelecting the music source Select the Fade function Turning the Daily Timer On and OffSetting the volume level Press the Cancel buttonWait for a few seconds Setting the Sleep TimerTimer Priority During playback a source, press the Sleep buttonAction TroubleshootingSymptom Possible CauseCare And Maintenance Specifications 0403MNMCREJEM
Top Page Image Contents