JVC LVT1040-003A manual Care And Maintenance

Page 33

Care And Maintenance

Handle your CDs carefully, and they will last a long time.

Compact Discs

• Only CDs bearing these marks can be used with this System. However, continued use of irregu- lar shape CDs (heart-shape, octagonal, etc.) can damage the System.

Remove the CD from its case by

holding it at the edges while press- ing the case’s center hole lightly.

• Do not touch the shiny surface of the CD, or bend the CD.

Put the CD back in its case after use to prevent warping.

• Be careful not to scratch the sur- face of the CD when placing it back in the case.

Avoid exposure to direct sunlight, temperature extremes, and moisture.

• A dirty CD may not play cor- rectly. If a CD does become dirty, wipe it with a soft cloth in a straight line from center to edge.

CAUTION:

Do not use any solvent (for example, con- ventional record cleaner, spray thinner, benzine, etc.) to clean a CD.

General Notes

In general, you will have the best performance by keeping your CDs and the mechanism clean.

Store CDs in their cases, and keep them in cabinets or on shelves.

Keep the System’s CD door closed when not in use.

Cleaning the Unit

Stains on the Unit

Should be wiped off with a soft cloth. If the Unit is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

Since the Unit may deteriorate in quality, become damaged or get its paint peeled off, be careful about the followings.

-DO NOT wipe it with a hard cloth.

-DO NOT wipe it strong.

-DO NOT wipe it with thinner or benzine.

-DO NOT apply any volatile substance such as insecti- cides to it.

-DO NOT allow any rubber or plastic to remain in con- tact with it for a long time.

Cleaning the Lens

If the lens in the CD pickup is dirty, dropout, etc., could de- grade sound.

Open the CD door and clean the lens as shown.

Use a blower (available from a camera store) to blow dust off the lens.

Blower

Lens

If there are fingerprints, etc. on the lens, gently wipe clean with a cotton swab.

Moisture Condensation

Moisture may condense on the lens inside the System in the following cases:

• After turning on heating in the room.

• In a damp room.

If the System is brought directly from a cold to a warm place.

Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours un- til the moisture evaporates, unplug the AC power cord, and then plug it in again.

30

Image 33
Contents FS-X1/FS-X3 Important for Laser Products Above ALL Features IntroductionHow This Manual Is Organized Table of Contents Troubleshooting Care And Maintenance Specifications How To Put Batteries In the Remote Control AccessoriesUsing the Remote Control Getting StartedConnecting the FM Antenna Using the Supplied Wire AntennaUsing the Coaxial Type Connector Not Supplied Connecting the AM MW Antenna Connecting the Speakers SP-FSX1/SP-FSX3 Connecting an External Equipment Connecting a Powered SubwooferWhen removing When attaching the speaker grillsAutomatic Power On Connecting an MD Recorder, etc Optical Digital OutputTurning the Power On and Off Basic OperationsChanging the Source Power Saving Mode Dimmer at Power Off Adjusting the Brightness Dimmer at Power OnAdjusting the Volume Fade-out Muting Fade MutingTo disable the A.P.off function No signal conditionAuto Power Off A.P.off Entering the Number with the Remote Control Numeric KeysTuning In a Station Using the TunerSelect a station using one of the follow- ing methods One Touch RadioTo Change the FM Reception Mode Presetting StationsTo change the preset stations, repeat the same Beat Cut AM MW ReceptionReceiving FM Stations with RDS To search for a program by PTY codesPress the PTY Search button within approx seconds again News AlarmAffairs InfoTest function Alarm functionWhen playing a CD-R or CD-RW Using the CD PlayerTo Insert a CD Quickest Way To Start a CD Is With the One Touch OperationBasics of Using the CD Player Normal Play To Unload a CDProgramming the Playing Order of the Tracks Program Play To Modify the Program Press the CD 6button on the Remote ControlRandom Play Repeat to program the other tracksLocking the CD door Repeating TracksUnlocking the CD door Turn off the systemListening to External Equipment Using External EquipmentsChanging the Equipment’s Name To exit the source LINE, select other source e.g. CDWhen the source is LINE, press and hold the SET button Adjusting the Input LevelPress the SET button to finish the adjustment Recording the System’s Source to External EquipmentSetting the Clock Using the TimersPress the CLOCK/TIMER button Press the 3 or 2 button to set the hourPerform steps 2 to 5 in Setting the Clo- ck on Setting the Daily TimerShowing the Clock Display Correcting the ClockSetting the on time Example Setting the OFF time ExampleSelecting the music source Setting the volume level Turning the Daily Timer On and OffPress the Cancel button Select the Fade functionTimer Priority Setting the Sleep TimerDuring playback a source, press the Sleep button Wait for a few secondsSymptom TroubleshootingPossible Cause ActionCare And Maintenance Specifications 0403MNMCREJEM