JVC LVT1040-003A manual Troubleshooting, Symptom, Possible Cause, Action

Page 32

Troubleshooting

If you are having a problem with your System, check this list for a possible solution before calling for service.

If you cannot solve the problem from the hints given here “ERROR!” appears on the display, or the System has been phys- ically damaged, call a qualified person, such as your dealer, for service.

Symptom

No sound is heard.

Poor radio reception

Stereo effect is lost in FM broadcast.

The CD skips.

The CD does not play.

Unable to operate the Remote Control.

Operations are disabled.

“CD NO DISC” appears.

“CD CAN’T PLAY” appears.

“CD DOOR ERROR” appears.

When the CD door is operating (open- ing or closing) while you are listening to FM, AM (MW) or LINE, the source is muted.

Some of the CD functions, such as skip or search, do not work correctly.

Possible Cause

Connections are incorrect, or loose.

Headphones are connected.

The antenna is disconnected.

The AM (MW) Loop Antenna is too close to the System.

The FM Wire Antenna is not prop- erly extended and positioned.

FM reception mode is changed to “FM MONO”.

The CD is dirty or scratched.

Track Skip marks are recorded.

The CD is upside down.

Track Skip mark is recorded for the first track of the disc.

The path between the Remote Con- trol and the sensor on the Unit is blocked.

The batteries have lost their charge.

The built-in microprocessor has mal- functioned due to external electrical in- terference.

There is no disc loaded.

You are trying to playback a CD which cannot be played, or there is a problem with the CD.

The disc has been inserted with its label side down.

The object is blocking the CD door to open.

This is one of the characteristics of this system.

You are playing an unfinalized disc.

Action

Check all connections and make cor- rections. (See pages 5 to 9.)

Disconnect the headphones.

Reconnect the antenna securely.

Change the position and direction of the AM (MW) Loop Antenna.

Extend FM Wire Antenna to the best reception position.

Press the FM/PLAY MODE button to select “FM AUTO”. (See page 14)

Clean or replace the CD.

This is normal.

Put the CD in with the label side up.

Wait until the Unit finds a track with- out a Track Skip mark.

Remove the obstruction.

Replace the batteries.

Unplug the System then plug it back in.

Insert a disc.

Change the disc.

Remove the disc and insert it with the label side up.

Press the 0 CD button to close the CD door and remove the object.

This is normal.

This is normal. If you need to use these functions, finalize the disc. (This Unit cannot finalize CD-R/CD-RW)

29

Image 32
Contents FS-X1/FS-X3 Important for Laser Products Above ALL How This Manual Is Organized FeaturesIntroduction Table of Contents Troubleshooting Care And Maintenance Specifications Accessories How To Put Batteries In the Remote ControlUsing the Remote Control Getting StartedUsing the Coaxial Type Connector Not Supplied Connecting the FM AntennaUsing the Supplied Wire Antenna Connecting the AM MW Antenna Connecting the Speakers SP-FSX1/SP-FSX3 Connecting a Powered Subwoofer Connecting an External EquipmentWhen removing When attaching the speaker grillsConnecting an MD Recorder, etc Optical Digital Output Automatic Power OnChanging the Source Turning the Power On and OffBasic Operations Adjusting the Brightness Dimmer at Power On Power Saving Mode Dimmer at Power OffAdjusting the Volume Fade-out Muting Fade MutingNo signal condition To disable the A.P.off functionAuto Power Off A.P.off Entering the Number with the Remote Control Numeric KeysUsing the Tuner Tuning In a StationSelect a station using one of the follow- ing methods One Touch RadioPresetting Stations To Change the FM Reception ModeTo change the preset stations, repeat the same Beat Cut AM MW ReceptionPress the PTY Search button within approx seconds again Receiving FM Stations with RDSTo search for a program by PTY codes Alarm NewsAffairs InfoAlarm function Test functionUsing the CD Player When playing a CD-R or CD-RWTo Insert a CD Quickest Way To Start a CD Is With the One Touch OperationProgramming the Playing Order of the Tracks Program Play Basics of Using the CD Player Normal PlayTo Unload a CD Press the CD 6button on the Remote Control To Modify the ProgramRandom Play Repeat to program the other tracksRepeating Tracks Locking the CD doorUnlocking the CD door Turn off the systemUsing External Equipments Listening to External EquipmentChanging the Equipment’s Name To exit the source LINE, select other source e.g. CDAdjusting the Input Level When the source is LINE, press and hold the SET buttonPress the SET button to finish the adjustment Recording the System’s Source to External EquipmentUsing the Timers Setting the ClockPress the CLOCK/TIMER button Press the 3 or 2 button to set the hourSetting the Daily Timer Perform steps 2 to 5 in Setting the Clo- ck onShowing the Clock Display Correcting the ClockSelecting the music source Setting the on time ExampleSetting the OFF time Example Turning the Daily Timer On and Off Setting the volume levelPress the Cancel button Select the Fade functionSetting the Sleep Timer Timer PriorityDuring playback a source, press the Sleep button Wait for a few secondsTroubleshooting SymptomPossible Cause ActionCare And Maintenance Specifications 0403MNMCREJEM