JVC LVT1040-003A manual Setting the on time Example, Setting the OFF time Example

Page 29

Using the Timers

On the Remote Control

1 Press the CLOCK/TIMER button repeat- edly until “ON (time)” appears on the display.

At this time, “DAILY” indicator blinks on the display. Each time you press the button, the display changes as follows.

DAILY ON?/DAILY OFF? = ON (time)* = Clock setting display = Cancelled = (back to the beginning)

*: Select this item!

The System enters ON-time setting mode, and the cur- rent ON time appears on the display and the hour digits blink.

2 Setting the ON time (Example: 10:15).

1.Press the 3 or 2 button to set the hour you want the System to come on, then press the SET button.

The minute digits of the ON time blink on the display. Pressing the 3 button moves the time forwards and pressing the 2 button moves it backwards.

Holding down the button moves the time.

2.Press the 3 or 2 button to set the minute, then press the SET button.

The System enters OFF-time setting mode, and the hour digits blink.

3 Setting the OFF time (Example: 13:30).

Note that the same time as the ON time cannot be set.

1.Press the 3 or 2 button to set the hour you want the System to be turned off, then press the SET button. The minute digits of the OFF time blink on the dis- play.

2.Press the 3 or 2 button to set the minute, then press the SET button.

The System enter the Music Source Selecting mode and “FM?” appears on the display.

4 Selecting the music source.

Press the 3 or 2 button to select the music source you want to listen to, then press the SET button.

Each time you press the 3 or 2 button, the display changes as shown below:

FM? Ô AM? Ô CD? Ô LINE?* Ô MELODY?

Ô(back to the beginning)

*: If the name has been changed, that name (e.g. “TAPE”) will appear. (See page 22.)

According to the music source you have selected, the next operation differs.

FM?

: Tunes in to the specified preset FM sta-

 

tion.

AM?

: Tunes in to the specified preset AM

 

(MW) station.

CD?

: Plays the specified track on the speci-

 

fied CD.

LINE?

: Plays an external source.

MELODY? : Select one of 10 melodies.

Preparation for each music source:

Perform the following operation according to the music source you have selected. Then, the System enters Vol- ume Setting mode.

When selecting “FM?” or “AM?”

Press the 3 or 2 button to select the preset station number, then press the SET button.

If you select the display “- -”, the current broad- cast station is selected.

When selecting “CD?”

Press the 3 or 2 button to select the track number you want to start playback, then press the SET button.

If you select the display “- -”, playback will start from the first track.

When selecting “LINE?”

Prepare the external equipment so that it will turn on at the ON time set by the System.

To allow this, the equipment should have the timer function.

When selecting “MELODY?”

Press the 3 or 2 button to select one of melodies (MELODY 1-10). Then, the selected melody is played back.

26

Image 29
Contents FS-X1/FS-X3 Important for Laser Products Above ALL How This Manual Is Organized FeaturesIntroduction Table of Contents Troubleshooting Care And Maintenance Specifications How To Put Batteries In the Remote Control AccessoriesUsing the Remote Control Getting StartedUsing the Coaxial Type Connector Not Supplied Connecting the FM AntennaUsing the Supplied Wire Antenna Connecting the AM MW Antenna Connecting the Speakers SP-FSX1/SP-FSX3 Connecting an External Equipment Connecting a Powered SubwooferWhen removing When attaching the speaker grillsAutomatic Power On Connecting an MD Recorder, etc Optical Digital OutputChanging the Source Turning the Power On and OffBasic Operations Power Saving Mode Dimmer at Power Off Adjusting the Brightness Dimmer at Power OnAdjusting the Volume Fade-out Muting Fade MutingTo disable the A.P.off function No signal conditionAuto Power Off A.P.off Entering the Number with the Remote Control Numeric KeysTuning In a Station Using the TunerSelect a station using one of the follow- ing methods One Touch RadioTo Change the FM Reception Mode Presetting StationsTo change the preset stations, repeat the same Beat Cut AM MW ReceptionPress the PTY Search button within approx seconds again Receiving FM Stations with RDSTo search for a program by PTY codes News AlarmAffairs InfoTest function Alarm functionWhen playing a CD-R or CD-RW Using the CD PlayerTo Insert a CD Quickest Way To Start a CD Is With the One Touch OperationProgramming the Playing Order of the Tracks Program Play Basics of Using the CD Player Normal PlayTo Unload a CD To Modify the Program Press the CD 6button on the Remote ControlRandom Play Repeat to program the other tracksLocking the CD door Repeating TracksUnlocking the CD door Turn off the systemListening to External Equipment Using External EquipmentsChanging the Equipment’s Name To exit the source LINE, select other source e.g. CDWhen the source is LINE, press and hold the SET button Adjusting the Input LevelPress the SET button to finish the adjustment Recording the System’s Source to External EquipmentSetting the Clock Using the TimersPress the CLOCK/TIMER button Press the 3 or 2 button to set the hourPerform steps 2 to 5 in Setting the Clo- ck on Setting the Daily TimerShowing the Clock Display Correcting the ClockSelecting the music source Setting the on time ExampleSetting the OFF time Example Setting the volume level Turning the Daily Timer On and OffPress the Cancel button Select the Fade functionTimer Priority Setting the Sleep TimerDuring playback a source, press the Sleep button Wait for a few secondsSymptom TroubleshootingPossible Cause ActionCare And Maintenance Specifications 0403MNMCREJEM