JVC LVT1040-003A manual To Unload a CD, Basics of Using the CD Player Normal Play

Page 22

Using the CD Player

❑You can insert a CD while listening to the other source.

•However, while the CD door is operating (opening or closing), the other source will be muted.

CAUTION:

•DO NOT try to open or close the CD door by hands as it will be damaged.

To Unload a CD

Take out the CD as shown below.

Basics of Using the CD Player

– Normal Play

To Play a CD

1 Select the source “CD”.

2 Insert a CD.

3 Press the 6button on the Unit or the CD 6button on the Remote Control.

The first track of the CD begins playing.

Track number

Playback time

•The CD Player automatically stops when the last track of the CD has finished playing.

To stop playing the CD, press the 7 button. The following information for the CD is displayed.

Total track number

Total playback time

To stop playing and remove the CD, press the 0CD button on the Unit or the CD DOOR 0 button on the Re- mote Control to open the CD door.

To pause, press the 6button on the Unit or the CD 6 button on the Remote Control. The playback time blinks on the display.

To cancel pause, press the same button again. Play con- tinues from the point where it was paused.

To Select a Track or Passage within a Track

During playback

Press the ¢ or 4 button on the Unit or the 3 or 2 but- ton on the Remote Control to select the track you want.

•The selected track starts playing.

•Press the ¢ (or 3) button once to skip to the beginning of the next track.

•Press the 4 (or 2) button to skip to the beginning of the track being played. Press twice quickly to skip to the beginning of the previous track.

•When the 3 or 2 button on the Remote Control is kept pressing, the track continuously skips.

•Press the Numeric Keys to select truck number (See page 12).

In Stop mode

•Press the ¢ or 4 (or 3 or 2) button to skip the track.

•Hold down the ¢ or 4 (or 3 or 2 ) button to continuously skip the tracks.

Search Play

Holding down the ¢ or 4 button on the Unit or the 5 or ∞ button on the Remote Control, during playback, will fast forward/backwards the CD so you can quickly find a particular passage in the track you are listening to.

Programming the Playing Order of the Tracks – Program Play

You can program up to 32 tracks in any desired order in- cluding the same tracks.

❑You can only make a program when the CD Player is stopped.

On the Remote Control

1 Insert a CD.

2 Press the CD 6button.

3 Press the 7 button to stop the CD.

4 Press the FM/PLAY MODE button until “CD PROGRAM” appears.

The System enters the Program Play mode and the “PRGM” indicator lights up.

Each time you press the button, the play mode changes as follows.

CD PROGRAM = CD RANDOM = CD NORMAL =(back to the beginning)

(After a few seconds)

•If already programmed, the track number and preset number of the last programmed track will appear.

19

Page 21 Page 23
Image 22
Page 21 Page 23
Contents FS-X1/FS-X3 Important for Laser Products Above ALL Introduction FeaturesHow This Manual Is Organized Table of Contents Troubleshooting Care And Maintenance Specifications Using the Remote Control AccessoriesHow To Put Batteries In the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied Connecting the AM MW Antenna Connecting the Speakers SP-FSX1/SP-FSX3 When removing Connecting a Powered SubwooferConnecting an External Equipment When attaching the speaker grillsConnecting an MD Recorder, etc Optical Digital Output Automatic Power OnBasic Operations Turning the Power On and OffChanging the Source Adjusting the Volume Adjusting the Brightness Dimmer at Power OnPower Saving Mode Dimmer at Power Off Fade-out Muting Fade MutingAuto Power Off A.P.off No signal conditionTo disable the A.P.off function Entering the Number with the Remote Control Numeric KeysSelect a station using one of the follow- ing methods Using the TunerTuning In a Station One Touch RadioTo change the preset stations, repeat the same Presetting StationsTo Change the FM Reception Mode Beat Cut AM MW ReceptionTo search for a program by PTY codes Receiving FM Stations with RDSPress the PTY Search button within approx seconds again Affairs AlarmNews InfoAlarm function Test functionTo Insert a CD Using the CD PlayerWhen playing a CD-R or CD-RW Quickest Way To Start a CD Is With the One Touch OperationTo Unload a CD Basics of Using the CD Player Normal PlayProgramming the Playing Order of the Tracks Program Play Random Play Press the CD 6button on the Remote ControlTo Modify the Program Repeat to program the other tracksUnlocking the CD door Repeating TracksLocking the CD door Turn off the systemChanging the Equipment’s Name Using External EquipmentsListening to External Equipment To exit the source LINE, select other source e.g. CDPress the SET button to finish the adjustment Adjusting the Input LevelWhen the source is LINE, press and hold the SET button Recording the System’s Source to External EquipmentPress the CLOCK/TIMER button Using the TimersSetting the Clock Press the 3 or 2 button to set the hourShowing the Clock Display Setting the Daily TimerPerform steps 2 to 5 in Setting the Clo- ck on Correcting the ClockSetting the OFF time Example Setting the on time ExampleSelecting the music source Press the Cancel button Turning the Daily Timer On and OffSetting the volume level Select the Fade functionDuring playback a source, press the Sleep button Setting the Sleep TimerTimer Priority Wait for a few secondsPossible Cause TroubleshootingSymptom ActionCare And Maintenance Specifications 0403MNMCREJEM
Top Page Image Contents