JVC LVT1040-003A manual Showing the Clock Display, Correcting the Clock, Setting the Daily Timer

Page 28

Using the Timers

3 Press the SET button.

The minute digits of the time indication blink on the dis- play.

•To return to the hour setting, press the CANCEL button.

4 Press the 3 or 2 button to set the minute. 5 Press the SET button.

“ADJUST OK!” appears on the display. The Clock in- dicator () remains lit. Then, the selected time is set and the seconds start counting from 0.

CAUTION:

•If there is a power failure, the clock loses its

setting. “0:00” and the Clock indicator () blinks on the display and the clock must be reset.

Showing the Clock (DISPLAY)

You can show the current time on the display.

To display the clock, press the DISPLAY button on the Remote Control.

To return to the normal display, press the same button

again.

Correcting the Clock

Use the following method to correct any clock shift.

❑You can correct the clock whether the System is turned on or off.

1 Repeatedly press the CLOCK/TIMER bu- tton to show the clock on the display.

Each time you press the button, the display changes as follows.

Example:

Alternates

(clock)

Display the source (clock is canceled)

2 Perform steps 2 to 5 in “Setting the Clo- ck” on page 24-25.

•When the System is in power saving mode, nothing ap- pears on the display. To see the clock, press the DIMMER button on the Remote Control.

•The clock may gain or lose one to two minutes per month.

•If there is a power failure, the clock loses its setting, “0:00” blinks on the display and the clock must be reset. To reset the clock, see “Setting the Clock” on page 24-25.

Setting the Daily Timer

Once you have set the Daily Timer, the timer will be acti- vated at the same time every day.

The “DAILY” indicator on the display shows that the Daily Timer you have set is in effect.

You can set the Daily Timer whether the System is on or off (but not in power saving mode (See page 11)).

•If you have made a mistake while setting the timer, press the CANCEL button on the Remote Control. However, this does not always cancel the current setting. If the CANCEL button does not work, press the CLOCK/TIMER button on the Remote Control repeatedly until the display returns to the original display, and start from the first step.

25

Image 28

Contents FS-X1/FS-X3 Important for Laser Products Above ALL Introduction FeaturesHow This Manual Is Organized Table of Contents Troubleshooting Care And Maintenance Specifications Accessories How To Put Batteries In the Remote ControlUsing the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied Connecting the AM MW Antenna Connecting the Speakers SP-FSX1/SP-FSX3 Connecting a Powered Subwoofer Connecting an External EquipmentWhen removing When attaching the speaker grillsConnecting an MD Recorder, etc Optical Digital Output Automatic Power OnBasic Operations Turning the Power On and OffChanging the Source Adjusting the Brightness Dimmer at Power On Power Saving Mode Dimmer at Power OffAdjusting the Volume Fade-out Muting Fade MutingNo signal condition To disable the A.P.off functionAuto Power Off A.P.off Entering the Number with the Remote Control Numeric KeysUsing the Tuner Tuning In a StationSelect a station using one of the follow- ing methods One Touch RadioPresetting Stations To Change the FM Reception ModeTo change the preset stations, repeat the same Beat Cut AM MW ReceptionTo search for a program by PTY codes Receiving FM Stations with RDSPress the PTY Search button within approx seconds again Alarm NewsAffairs InfoAlarm function Test functionUsing the CD Player When playing a CD-R or CD-RWTo Insert a CD Quickest Way To Start a CD Is With the One Touch OperationTo Unload a CD Basics of Using the CD Player Normal PlayProgramming the Playing Order of the Tracks Program Play Press the CD 6button on the Remote Control To Modify the ProgramRandom Play Repeat to program the other tracksRepeating Tracks Locking the CD doorUnlocking the CD door Turn off the systemUsing External Equipments Listening to External EquipmentChanging the Equipment’s Name To exit the source LINE, select other source e.g. CDAdjusting the Input Level When the source is LINE, press and hold the SET buttonPress the SET button to finish the adjustment Recording the System’s Source to External EquipmentUsing the Timers Setting the ClockPress the CLOCK/TIMER button Press the 3 or 2 button to set the hourSetting the Daily Timer Perform steps 2 to 5 in Setting the Clo- ck onShowing the Clock Display Correcting the ClockSetting the OFF time Example Setting the on time ExampleSelecting the music source Turning the Daily Timer On and Off Setting the volume levelPress the Cancel button Select the Fade functionSetting the Sleep Timer Timer PriorityDuring playback a source, press the Sleep button Wait for a few secondsTroubleshooting SymptomPossible Cause ActionCare And Maintenance Specifications 0403MNMCREJEM